BenQ W5000, W20000 Creating your own startup screen, Personalizing the projector menu display

Page 33

W20000-en.book Page 33 Monday, October 22, 2007 3:35 PM

Creating your own startup screen

In addition to selecting the projector preset startup screen from among BenQ logo or Blue screen, you can make your own startup screen that is a picture projected from your computer or video source.

To create your own startup screen, project the picture you want to use as your startup screen from either a computer or video source. The rest steps are as follows.

•Using the OSD menu

1.Press MENU and then press / until the System Setup menu is

 

highlighted.

System Setup

 

2.

Press

to highlight My Screen and press ENTER. A confirmation message

Language

English

Splash Screen

My Screen

 

displays.

 

My Screen

ENTER

 

 

Projector Position

Floor Front

3.

Press ENTER again.

Auto Off

Disable

Sleep Timer

Disable

4.

The message 'Screen Capturing...' displays while the projector is processing

Background Color

Blue

Menu Settings

 

 

the picture. Please wait.

Input Source

 

 

Auto Source Search

On

5.

If the action is successful, you see the message 'Captured Succeeded' on the

S-Video

EXIT Back

 

screen. The captured picture is saved as My Screen.

 

 

6.To view the captured picture displayed as the startup screen, set My Screen in the System Setup > Splash Screen menu and restart the projector.

In the unlikely event that the capturing action fails, change your target picture.

Personalizing the projector menu display

The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance.

•Rename User Mode: See "Renaming user modes" on page 25 for details.

•Menu Display Time in the System Setup > Menu Settings menu sets the length of time the OSD will remain active

after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time.

•Menu Position in the System Setup > Menu Settings menu sets the OSD position in five locations. Use / to select a preferred position.

•Language in the System Setup menu sets your familiar language for the On-Screen (OSD) Menus. See "Using the menus" on page 20 for details.

•Splash Screen in the System Setup menu sets a preferred logo screen to be displayed during projector start-up. See "Creating your own startup screen" on page 33 for details.

Locking control keys

With the control keys on the remote control and projector locked, you can prevent your projector settings from being changed accidentally (by children, for example). When Key Lock is on, no control keys on the remote control and projector will operate except POWER and EXIT.

English

To lock the keys:

•Using the OSD menu

1.Press MENU and then press / until the Advanced Setup menu is highlighted.

2.Press to highlight Key Lock, and press ENTER. The control keys lock. To unlock the keys, press and hold EXIT on the projector or remote control for 5 seconds.

Advanced Setup

Lamp

Pattern

Dust Filter

 

High Altitude Mode

Off

Password

 

Key Lock

ENTER

Reset All Settings

 

ISF

 

S-Video

EXIT Back

Using the projector

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents W20000/W5000 Digital Projector Home Cinema Series WelcomeTable of contents Important safety instructions Do not block the ventilation holes while During operation. It may harm your sightDo not step on the projector or place any objects upon it Avoid volatile liquid Moisture condensationDisposal Ceiling mounting the projectorRemote control batteries Shipping contentsRemote control operation OverviewProjector features Projector exterior view Connector panelFront and upper side view Rear viewControl panel Controls and functionsRemote control Choosing a location Positioning your projectorShifting the projection lens vertically Obtaining a preferred projected image sizeDetermine the aspect ratio of your screen, 169 or 43? Installation for a 169 ratio screen Projection dimensionsWidescreen ratio screen dimension table With min Position Zoom Cm C Cm DInstallation for a 43 ratio screen Min Max Highest Lowest ImageDiagonal Preparations Connecting with video equipmentBest video quality Better video qualityConnecting Hdmi devices Connecting Rgbhv devicesConnecting component-video devices Connecting S-Video or video devices Connecting a computerConnect the projector to a computer with a VGA-BNC cable Using the remote control or projector Using the projectorUsing the OSD menu Turning the projector onFine-tuning the image size and clarity Using the menusUse / to highlight the System Setup menu Adjust the projected picture to the size that youUtilizing the password function Using a security cable lockSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Confirm the new password by re-entering the new passwordAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Two parallel sidesSelecting a preset mode Using the preset and user modesFine-tuning the selected picture mode Using the remote controlResetting the picture mode Setting the User 1/User 2/User 3 modeRenaming user modes Enter and ExitFine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image clarityTo set a preferred color temperature Setting a preferred color temperatureTo adjust and store the settings Color ManagementSelecting a Gamma setting Adjusting Brilliant ColorAdjusting contrast ratio via Iris Using the remote controlTheir original width using this setting Selecting the aspect ratioAbout the aspect ratio To activate High Altitude Mode Using Panamorph lenses optionalOperating in a high altitude environment Suitable for use with PC and Rgbhd source inputsDisplaying more than one image source simultaneously Disabled functions for the active windowsPIP source conflict list Highlight PIP and press / to select OnCreating your own startup screen Personalizing the projector menu displayLocking control keys Commands during the cooling process Turning the power offOn-Screen Display OSD structure On-Screen Display OSD menusSystem Setup SetupInformation Picture -- Advanced menu Picture -- Basic menuDisplay menu System Setup menuAdvanced Setup menu Information menu ResolutionSource Lamp HoursCare of the projector Additional informationResetting the filter timer To clean the filterLamp information Setting Auto OffGetting to know the lamp hour Extending lamp lifeReplacing the lamp Timing of replacing the lampPulling it too quickly may cause the lamp to Tighten the screws securing the lamp boxAfter the startup logo, press Menu and then press / until Resetting the lamp timerIndicators Troubleshooting Dimensions SpecificationsOptical ElectricalFormat Resolution Refresh rateHz Freq.KHz Pixel Freq.MHz Timing chartSupported timing for Video and S-Video inputs Supported timing for Hdmi inputWarranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users MIC statement
Top Page Image Contents