BenQ MX764 user manual Remote control, 22 12. Network, Auto, Keystone/Arrow buttons / Up Down

Page 11

Remote control

1

2

3

4

5

6

7

8

9

10

11

1.ON/OFF

6.MODE/ENTER

Selects an available picture setup mode.

		Activates the selected On-Screen Display
12		(OSD) menu item.
13	7.	LASER
14		Emits visible laser pointer light for
		presentation purposes.

158. PAGE UP/PAGE DOWN

	16		Operates your display software program
	16		(on a connected PC) which responds to
			page up/down commands (like Microsoft
	15		PowerPoint).
	17	9.	FREEZE
			Freezes the projected image.
	18	10.	NETWORK SETTING
	19		Enters network setting directly.
	19	11.	TEST
	20	11.	TEST
	21		Displays the test pattern.

22 12. NETWORK

23Searches the network signal and project it within a few seconds once available.

13.SOURCE

Toggles the projector between standby mode and on.

2.Source selection buttons (COMPUTER-1, COMPUTER-2, VIDEO, S-VIDEO)

Selects an input source for display.

3.MENU/EXIT

Displays the source selection bar.

14.AUTO

Automatically determines the best picture timings for the displayed image.

15.Keystone/Arrow buttons ( / Up, /

Down)

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

4.BLANK

Used to hide the screen image.

5. Left

Manually corrects distorted images resulting from an angled projection.

16. Right

When the On-Screen Display (OSD) menu is activated, the #5, #15 and #16 buttons are used as directional arrows to select the desired menu items and to make adjustments.

Introduction 11

Image 11

Contents

MX763/MX764 Digital Projector WelcomeTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Safety Instructions Confined. Allow at least 50 cm clearance Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions Keystone/Arrow buttons / Up Down Remote control22 12. Network AutoNumeric buttons VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer MIC/VOL +Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsShifting the projection lens When the projector position is fixedConnection ConnectionConnecting audio Connecting video source devicesAbout the microphone input Audio Settings Microphone Volume menuPlaying sound through the projector Connection Starting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusSecuring the projector Using a security cable lockUtilizing the password function Setting a passwordChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes RED Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Hiding the image Remote paging operationsFreezing the image Operating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionSetting the Infrastructure mode Operation Controlling the projector remotely through a web browser Operation Operation Iii Press Exit to go back to the remote network operation Operation Operation Using the web control lock Displaying images through QPresenter Downloading and installing QPresenterUsing QPresenter Operation Operation Using the Projection Login Code Using the USB cable to display computer contentUsing the broadcasting function Presenting from a USB Reader Shutting down the projector Using the USB CameraDirect power off Basic Menu operationMenu system Main menu Sub-menu OptionsAdvanced System Setup BasicDhcp Main menu Sub-menu Options System Setup AdvancedDescription of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save SettingsColor Space TimerFunction Description Quick Auto SearchOperation SettingsPanel Key Advanced menu Security Settings DescriptionRemote ReceiverClosed System Setup Advanced menu Function DescriptionBaud Rate Test PatternCurrent Reset AllInformation menu Function Description NetworkCare of the projector MaintenanceExtending lamp life Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Ensure the handle is fully laid flat and locked in place Tighten the screws that secure the lamp cover Resetting the lamp timerThermal events IndicatorsLight Status & Description Power events Lamp eventsCause Remedy TroubleshootingProjector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputDisclaimer Warranty and Copyright informationLimited warranty Copyright