BenQ MX764 Securing the projector, Using a security cable lock, Utilizing the password function

Page 25
INPUT NEW PASSWORD
Power On Lock and Splash Screen Lock use the same password.
MENU Back

Securing the projector

Using a security cable lock

The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock, such as the Kensington lock, to secure the projector. You can locate a Kensington lock slot on the projector.

A Kensington security cable lock is usually a combination of key(s) and the lock. Refer to the lock’s documentation for finding out how to use it.

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu.

WARNING: You will be inconvenienced if you activate the password functionality and subsequently forget the password. Print out this manual (if necessary) and write the password you used in this manual, and keep the manual in a safe place for later recall.

Setting a password

Once a password has been set and the power on lock is activated, the projector cannot be used unless the correct password is entered every time the projector is started.

1.Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings menu. Press MODE/ENTER. The Security Settings page is displayed.

2.Highlight Change Security Settings and press MODE/ENTER.

3. As pictured to the right, the four arrow keys (, , , ) respectively represent 4 digits (1, 2, 3, 4). According to the password you desire to set,

press the arrow keys to enter six digits for the password.

4.Confirm the new password by re-entering the new password.

Once the password is set, the OSD menu returns to the Security Settings page.

5.To activate the Power On Lock function, press / to highlight Power On Lock and press / to select On.

6.To activate the Splash Screen Lock function, press / to highlight Splash Screen Lock and press / to select On.

When the Splash Screen Lock is activated, the My Screen function in the SYSTEM SETUP: Basic menu will be password-protected.

IMPORTANT: The digits being input will be displayed as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

7.To leave the OSD menu, press MENU/EXIT.

Operation 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents MX763/MX764 Digital Projector WelcomeTable of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions 22 12. Network Remote controlAuto Keystone/Arrow buttons / Up DownOperating the Laser pointer VOLUME+/VOLUME- Adjusts the sound level MuteMIC/VOL + Numeric buttonsReplacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsShifting the projection lens When the projector position is fixedConnection ConnectionConnecting audio Connecting video source devicesPlaying sound through the projector Audio Settings Microphone Volume menuAbout the microphone input Connection Starting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusUtilizing the password function Using a security cable lockSetting a password Securing the projectorEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes RED To cancel the timer, perform the following steps Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right Freezing the image Remote paging operationsHiding the image Using the remote control To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundAdjusting the microphone volume Turning off the Power On/Off Ring ToneCable connection Controlling the projector through a LAN environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentSetting the Infrastructure mode Wireless connectionHighlight Wireless LAN and press MODE/ENTER Operation Controlling the projector remotely through a web browser Operation Operation Iii Press Exit to go back to the remote network operation Operation Operation Using the web control lock Using QPresenter Downloading and installing QPresenterDisplaying images through QPresenter Operation Operation Using the broadcasting function Using the USB cable to display computer contentUsing the Projection Login Code Presenting from a USB Reader Shutting down the projector Using the USB CameraDirect power off Menu system Menu operationMain menu Sub-menu Options BasicAdvanced System Setup BasicDhcp Main menu Sub-menu Options System Setup AdvancedDescription of each menu Temperature Picture ModeManagement Save Settings Display menu Picture menu Function Description TeachingFunction Description Quick Auto TimerSearch Color SpaceOperation SettingsRemote Advanced menu Security Settings DescriptionReceiver Panel KeyBaud Rate System Setup Advanced menu Function DescriptionTest Pattern ClosedInformation menu Function Description Reset AllNetwork CurrentCare of the projector MaintenanceLamp information Setting Lamp Mode as EconomicGetting to know the lamp hour Extending lamp lifeStatus Message Timing of replacing the lampReplacing the lamp Ensure the handle is fully laid flat and locked in place Tighten the screws that secure the lamp cover Resetting the lamp timerLight Status & Description Power events IndicatorsLamp events Thermal eventsCause Remedy TroubleshootingProjector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputLimited warranty Warranty and Copyright informationCopyright Disclaimer
Top Page Image Contents