BenQ MX764 user manual Ensure the handle is fully laid flat and locked in place

Page 70

7.Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector.

•Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

•Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.

1

2

•Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

8.As shown in the figure, lower the new lamp first into the connector on the projector and reconnect the lamp connector.

9.Tighten the screw that secures the lamp.

•Loose screw may cause a bad connection, which could result in malfunction.

•Do not over tighten the screw.

10.Ensure the handle is fully laid flat and locked in place.

11.Place the lamp protection film supplied with the new lamp on the lamp compartment.

12.Replace the lamp cover on the projector.

2 1

70 Maintenance

Image 70

Contents Welcome MX763/MX764 Digital ProjectorTable of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Ceiling mounting the projector Projector features IntroductionShipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions Auto Remote control22 12. Network Keystone/Arrow buttons / Up DownMIC/VOL + VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer Numeric buttonsRemote control effective range Replacing the remote control batteriesFront Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeWhen the projector position is fixed Shifting the projection lensConnection ConnectionConnecting video source devices Connecting audioPlaying sound through the projector Audio Settings Microphone Volume menuAbout the microphone input Connection Operation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Using the menus Use / to highlight the System Setup Basic menuSetting a password Using a security cable lockUtilizing the password function Securing the projectorEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes RED To cancel the timer, perform the following steps Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right Freezing the image Remote paging operationsHiding the image Locking control keys To activate the High Altitude ModeUsing the remote control Operating in a high altitude environmentAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneIf you are in a Dhcp environment Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environmentSetting the Infrastructure mode Wireless connectionHighlight Wireless LAN and press MODE/ENTER Operation Controlling the projector remotely through a web browser Operation Operation Iii Press Exit to go back to the remote network operation Operation Operation Using the web control lock Using QPresenter Downloading and installing QPresenterDisplaying images through QPresenter Operation Operation Using the broadcasting function Using the USB cable to display computer contentUsing the Projection Login Code Presenting from a USB Reader Using the USB Camera Shutting down the projectorDirect power off Main menu Sub-menu Options Menu operationMenu system BasicSystem Setup Basic AdvancedMain menu Sub-menu Options System Setup Advanced DhcpDescription of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSearch TimerFunction Description Quick Auto Color SpaceSettings OperationReceiver Advanced menu Security Settings DescriptionRemote Panel KeyTest Pattern System Setup Advanced menu Function DescriptionBaud Rate ClosedNetwork Reset AllInformation menu Function Description CurrentMaintenance Care of the projectorGetting to know the lamp hour Setting Lamp Mode as EconomicLamp information Extending lamp lifeTiming of replacing the lamp Status MessageReplacing the lamp Ensure the handle is fully laid flat and locked in place Resetting the lamp timer Tighten the screws that secure the lamp coverLamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Cause RemedySpecifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsCopyright Warranty and Copyright informationLimited warranty Disclaimer