BenQ MX764 user manual Wireless connection, Setting the Infrastructure mode

Page 39

Wireless connection

To connect to the projector wirelessly, you have to plug a BenQ wireless dongle (optional) to the USB Type A connector on the projector, and then only a few OSD configuration steps are required.

1.Make sure the projector is turned on.

2.Do one of the following:

•Press NETWORK SETTING on the remote control. The Network Settings page is displayed.

•Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted. Press to highlight Network Settings and press MODE/ ENTER. The Network Settings page is displayed.

3.Highlight Wireless LAN and press MODE/ENTER.

4.Make sure the Status is Connect.

5.Make sure the SSID information is displayed.

6.Press to highlight Connection Mode and press / to select AP or Infrastructure. In AP mode, you need to use your computer’s wireless connection utility to search the projector’s SSID and connect to it. Then you can search the projector with QPresenter.

Setting the Infrastructure mode

1.Connect both the RJ45 cable and wireless dongle to the USB ports of the projector.

2.Open the Admin page of the Projector Network Display System and log in.

See "Controlling the projector remotely through a web browser" on page 41 for how to use the Projector Network Display System.

3.Go to the Wireless LAN page and change the Connection mode to Infrastructure mode.

Operation 39

Image 39

Contents MX763/MX764 Digital Projector WelcomeTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Ceiling mounting the projector Introduction Projector featuresShipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Keystone/Arrow buttons / Up Down Remote control22 12. Network AutoNumeric buttons VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer MIC/VOL +Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsShifting the projection lens When the projector position is fixedConnection ConnectionConnecting audio Connecting video source devicesAudio Settings Microphone Volume menu Playing sound through the projectorAbout the microphone input Connection Starting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusSecuring the projector Using a security cable lockUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes RED Setting the presentation timer To cancel the timer, perform the following stepsTop-Left Bottom-Left Top-Right Bottom-Right Remote paging operations Freezing the imageHiding the image Operating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentWireless connection Setting the Infrastructure modeHighlight Wireless LAN and press MODE/ENTER Operation Controlling the projector remotely through a web browser Operation Operation Iii Press Exit to go back to the remote network operation Operation Operation Using the web control lock Downloading and installing QPresenter Using QPresenterDisplaying images through QPresenter Operation Operation Using the USB cable to display computer content Using the broadcasting functionUsing the Projection Login Code Presenting from a USB Reader Shutting down the projector Using the USB CameraDirect power off Basic Menu operationMenu system Main menu Sub-menu OptionsAdvanced System Setup BasicDhcp Main menu Sub-menu Options System Setup AdvancedDescription of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save SettingsColor Space TimerFunction Description Quick Auto SearchOperation SettingsPanel Key Advanced menu Security Settings DescriptionRemote ReceiverClosed System Setup Advanced menu Function DescriptionBaud Rate Test PatternCurrent Reset AllInformation menu Function Description NetworkCare of the projector MaintenanceExtending lamp life Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Ensure the handle is fully laid flat and locked in place Tighten the screws that secure the lamp cover Resetting the lamp timerThermal events IndicatorsLight Status & Description Power events Lamp eventsCause Remedy TroubleshootingProjector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputDisclaimer Warranty and Copyright informationLimited warranty Copyright