BenQ MX764 user manual Main menu Sub-menu Options System Setup Advanced, Dhcp

Page 58

Main menu Sub-menu

Options

5. SYSTEM SETUP: Advanced

	Baud Rate		2400/4800/9600/14400/19200/
	Baud Rate		38400/57600/115200
			38400/57600/115200
	Test Pattern		On/Off
		Closed Caption	On/Off
	Closed Caption Enable		On/Off
	Closed Caption Enable
		Caption Version	CC1/CC2/CC3/CC4
		Network	On/Off
	Standby	Microphone	On/Off
	Standby	Monitor Out	On/Off
	Settings	Monitor Out	On/Off
	Settings	Audio Pass	On/Off
		Audio Pass
		Through
		Through
			Status
			DHCP
		Wired LAN	IP Address
		Wired LAN	Subnet Mask
			Default Gateway
			DNS Server
			Apply
			Status
	Network	Wireless LAN	SSID
		Wireless LAN	IP Address
			IP Address
	Settings
	Settings		Connection Mode
		Remote Desktop	Account
		Remote Desktop	Password
			Connect
		Projection Log In	On/Off
		Code

Broadcasting

	AMX Device	On/Off
	Discovery	On/Off
	Discovery
	Mac Address

	Reset All Settings
		•	Source
6.		•	Picture Mode
6.	Current System Status	•	Resolution
INFORMATION	Current System Status	•	Color System
		•	Equivalent Lamp Hour
		•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

58 Operation

Image 58

Contents Welcome MX763/MX764 Digital ProjectorTable of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Ceiling mounting the projector Projector features IntroductionShipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions Auto Remote control22 12. Network Keystone/Arrow buttons / Up DownMIC/VOL + VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer Numeric buttonsRemote control effective range Replacing the remote control batteriesFront Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeWhen the projector position is fixed Shifting the projection lensConnection ConnectionConnecting video source devices Connecting audioPlaying sound through the projector Audio Settings Microphone Volume menuAbout the microphone input Connection Operation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Using the menus Use / to highlight the System Setup Basic menuSetting a password Using a security cable lockUtilizing the password function Securing the projectorEntering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes RED To cancel the timer, perform the following steps Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right Freezing the image Remote paging operationsHiding the image Locking control keys To activate the High Altitude ModeUsing the remote control Operating in a high altitude environmentAdjusting the microphone volume Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneIf you are in a Dhcp environment Controlling the projector through a LAN environmentCable connection If you are in a non-DHCP environmentSetting the Infrastructure mode Wireless connectionHighlight Wireless LAN and press MODE/ENTER Operation Controlling the projector remotely through a web browser Operation Operation Iii Press Exit to go back to the remote network operation Operation Operation Using the web control lock Using QPresenter Downloading and installing QPresenterDisplaying images through QPresenter Operation Operation Using the broadcasting function Using the USB cable to display computer contentUsing the Projection Login Code Presenting from a USB Reader Using the USB Camera Shutting down the projectorDirect power off Main menu Sub-menu Options Menu operationMenu system BasicSystem Setup Basic AdvancedMain menu Sub-menu Options System Setup Advanced DhcpDescription of each menu Management Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSearch TimerFunction Description Quick Auto Color SpaceSettings OperationReceiver Advanced menu Security Settings DescriptionRemote Panel KeyTest Pattern System Setup Advanced menu Function DescriptionBaud Rate ClosedNetwork Reset AllInformation menu Function Description CurrentMaintenance Care of the projectorGetting to know the lamp hour Setting Lamp Mode as EconomicLamp information Extending lamp lifeTiming of replacing the lamp Status MessageReplacing the lamp Ensure the handle is fully laid flat and locked in place Resetting the lamp timer Tighten the screws that secure the lamp coverLamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Cause RemedySpecifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsCopyright Warranty and Copyright informationLimited warranty Disclaimer