BenQ MX764 user manual Important safety instructions, Safety Instructions

Page 3

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1.Please read this manual before you operate your projector. Save it for future reference.

2.Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.

3.Refer servicing to qualified service personnel.

5.In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC,

but could fail if power cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS).

6.Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press BLANK on the projector or remote control.

4.Always open the lens shutter (if any) or remove the lens cap (if any) when the projector lamp is on.

Important safety instructions

3

Image 3

Contents MX763/MX764 Digital Projector WelcomeTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Ceiling mounting the projector Introduction Projector featuresShipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Keystone/Arrow buttons / Up Down Remote control22 12. Network AutoNumeric buttons VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer MIC/VOL +Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsShifting the projection lens When the projector position is fixedConnection ConnectionConnecting audio Connecting video source devicesAudio Settings Microphone Volume menu Playing sound through the projectorAbout the microphone input Connection Starting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusSecuring the projector Using a security cable lockUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes RED Setting the presentation timer To cancel the timer, perform the following stepsTop-Left Bottom-Left Top-Right Bottom-Right Remote paging operations Freezing the imageHiding the image Operating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentWireless connection Setting the Infrastructure modeHighlight Wireless LAN and press MODE/ENTER Operation Controlling the projector remotely through a web browser Operation Operation Iii Press Exit to go back to the remote network operation Operation Operation Using the web control lock Downloading and installing QPresenter Using QPresenterDisplaying images through QPresenter Operation Operation Using the USB cable to display computer content Using the broadcasting functionUsing the Projection Login Code Presenting from a USB Reader Shutting down the projector Using the USB CameraDirect power off Basic Menu operationMenu system Main menu Sub-menu OptionsAdvanced System Setup BasicDhcp Main menu Sub-menu Options System Setup AdvancedDescription of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save SettingsColor Space TimerFunction Description Quick Auto SearchOperation SettingsPanel Key Advanced menu Security Settings DescriptionRemote ReceiverClosed System Setup Advanced menu Function DescriptionBaud Rate Test PatternCurrent Reset AllInformation menu Function Description NetworkCare of the projector MaintenanceExtending lamp life Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Ensure the handle is fully laid flat and locked in place Tighten the screws that secure the lamp cover Resetting the lamp timerThermal events IndicatorsLight Status & Description Power events Lamp eventsCause Remedy TroubleshootingProjector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputDisclaimer Warranty and Copyright informationLimited warranty Copyright