BenQ MX764 Remote, Receiver, Panel Key, Lock, Background, Splash, My Screen, High, Altitude

Page 63

		Function
		Remote
		Remote
	4.	Receiver
	SYSTEM	Panel Key
		Panel Key
	SETUP:	Lock
	SETUP:	Background
		Background
		Color
	Basic	Splash
	Basic	Screen
	menu	My Screen
		My Screen
		High
		Altitude
		Mode
	5.	Audio
	SYSTEM	Settings
	SYSTEM
	SETUP:	Settings
		Lamp
	Advanced menu	Security
		Settings

Description

Allows you to enable all the remote receivers or one specific remote receiver on the projector.

Disables or enables all panel key functions except POWER on the projector and keys on the remote control. See "Locking control keys" on page 36 for details.

Sets the background color for the projector.

Allows you to select which logo screen will display during projector start-up. The following options are available: BenQ logo, My Screen, Black screen, Blue screen.

Captures and stores the projected picture as My Screen. See "Creating your own startup screen" on page 36 for details.

In the unlikely event that the capturing action fails, change your target picture.

A mode for operation in high altitude areas. See "Operating in a high altitude environment" on page 36 for details.

Mute

Volume

Microphone Volume

Power On/Off Ring Tone

See "Adjusting the sound" on page 37 for details.

Lamp Mode

See "Setting Lamp Mode as Economic" on page 67 for details.

Reset lamp timer

See "Resetting the lamp timer" on page 71 for details.

Equivalent Lamp Hour

See "Getting to know the lamp hour" on page 67 for details on how the total lamp hour is calculated.

Change Password

You will be asked to enter the current password before changing to a new one. See "Utilizing the password function" on page 25 for details.

Change Security Settings

Power On Lock

Splash Screen Lock

See "Utilizing the password function" on page 25 for details.

Web Control Lock

See "Using the web control lock" on page 48 for details.

Operation 63

Image 63

Contents

MX763/MX764 Digital Projector WelcomeTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Ceiling mounting the projector Introduction Projector featuresShipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Keystone/Arrow buttons / Up Down Remote control22 12. Network AutoNumeric buttons VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer MIC/VOL +Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsShifting the projection lens When the projector position is fixedConnection ConnectionConnecting audio Connecting video source devicesAudio Settings Microphone Volume menu Playing sound through the projectorAbout the microphone input Connection Starting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusSecuring the projector Using a security cable lockUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureChanging the password Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes RED Setting the presentation timer To cancel the timer, perform the following stepsTop-Left Bottom-Left Top-Right Bottom-Right Remote paging operations Freezing the imageHiding the image Operating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentWireless connection Setting the Infrastructure modeHighlight Wireless LAN and press MODE/ENTER Operation Controlling the projector remotely through a web browser Operation Operation Iii Press Exit to go back to the remote network operation Operation Operation Using the web control lock Downloading and installing QPresenter Using QPresenterDisplaying images through QPresenter Operation Operation Using the USB cable to display computer content Using the broadcasting functionUsing the Projection Login Code Presenting from a USB Reader Shutting down the projector Using the USB CameraDirect power off Basic Menu operationMenu system Main menu Sub-menu OptionsAdvanced System Setup BasicDhcp Main menu Sub-menu Options System Setup Advanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save SettingsColor Space TimerFunction Description Quick Auto SearchOperation SettingsPanel Key Advanced menu Security Settings DescriptionRemote ReceiverClosed System Setup Advanced menu Function DescriptionBaud Rate Test PatternCurrent Reset AllInformation menu Function Description NetworkCare of the projector MaintenanceExtending lamp life Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Ensure the handle is fully laid flat and locked in place Tighten the screws that secure the lamp cover Resetting the lamp timerThermal events IndicatorsLight Status & Description Power events Lamp eventsCause Remedy TroubleshootingProjector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputDisclaimer Warranty and Copyright informationLimited warranty Copyright