BenQ MW767, MX766, MX822ST user manual Projector exterior view, Front/upper side

Page 10

Projector exterior view

Front/upper side

(MX766/MW767)

1

2

6

3


4										7
										7
							8


5								9
								9
									10

(MX822ST)

1

1.External control panel

(See "Projector" on page 12 for details.)

2.Lamp cover

3.Focus ring (MX766/MW767) Focus slide lever (MX822ST)

4.Projection lens

5.Lens cover

6.Vent (heated air exhaust)

7.Speaker

8.Zoom slide lever (MX766/MW767)

9.Front IR remote sensor

10.Quick-release button

2

4

6

7

3

9

5	10

10 Introduction

Image 10

Contents MX766/MW767/MX822ST Digital Projector Table of contents Do not look straight at Important safety instructionsSafety Instructions Projector lens during operationSafety Instructions Do not block the ventilation holes Safety Instructions Projector features IntroductionShipping contents Optional accessories Projector exterior view Front/upper sideRear/lower side MX822STControls and functions Volume /Arrow keys / Left, / RightPower/POWER indicator light Keystone/Arrow keys / Up DownMounting the projector Zoom + Remote controlVolume /Arrow keys / Left Right TestAuto Operating the laser pointerHdmi MIC/VOL +Replacing the remote control battery Choosing a location Set Rear Ceiling in the System Setup BasicPositioning your projector Front TableObtaining a preferred projected image size MW767 Projection dimensionsMX766 Max length Inch Max. zoom Min. zoomMX822ST Connection Operation System Minimum Hardware Requirements Connecting a computer or monitor Connecting a computerConnecting a monitor To connect the projector to a monitorConnecting an Hdmi source device Connecting Video source devicesTo connect the projector to an Hdmi source device Connecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video/composite source device To connect the projector to an S-Video/Video source deviceConnecting with document camera Operation Starting up the projectorAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Using build-in test pattern Fine-tuning the image size and clarityCorrecting keystone MODE/ENTER . The Keystone correctionUsing the menus Language and press Enter toSetting a password Using a security cable lockUtilizing the password function If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Switching input signalChanging Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratioSelecting a picture mode Optimizing the imageUsing Wall Color Fine-tuning the image quality in user modesAdjusting Brilliant Color Adjusting TintAdjusting Sharpness Selecting a Color TemperaturePress MODE/ENTER and the 3D Color Management page displays Setting the presentation timer To cancel the timer, perform the following stepsHiding the image Remote paging operationsFreezing the image Operating in a high altitude environment Adjusting the soundAdjusting the sound level Muting the soundAdjusting the microphone’s sound level Turning off the Power on/off ring tonePersonalizing the projector menu display Select the lamp saver mode Until the System Setup Advanced menu is highlightedUse Teaching Template Controlling the projector through a LAN environment Configuring the Wired LAN SettingsConfiguring the Wireless LAN Settings If you are in a Dhcp environmentControlling the projector remotely through a web browser Through Q Presenter on page 59 for details Page Page Iii Page Page Page Page Displaying image through Q Presenter Iii Iii Vii Using the Web Control Lock Using the Projection Login CodeImage File Types Using the broadcassting functionPresenting From a USB Reader PreparationControlling USB Reader PressPress Settings Remote Desktop Control through Q Presenter Enter PointDraw Pen Shutting down the projectorMenu operation Menu systemSystem Setup Basic CC1/CC2/CC3/CC4 Dhcp Description of each menu Display menu3D Mode 3D Sync InvertPicture mode on page 39 for details Picture menuPicture menu Source menu System Setup Basic menu Auto Power Off Direct Power OnSignal Power On Blank TimerSee PointDraw Pen on page 70 for details System Setup Advanced menu Closed Caption Enable Caption VersionNetwork Wired LANWireless LAN MicrophoneResolution System Setup Advanced menu Information menuPicture Mode SourceMaintenance Care of the projectorLamp information Setting Lamp Mode eco function as Economic or SmartEco modeSetting Auto Power Off Getting to know the lamp hourPage Timing of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Tighten the screws that secure LampLight Status & Description IndicatorsLamp events Thermal Sensor 2 short error Thermal Sensor 2 open errorThermal IC #2 I2C Connection error Troubleshooting Specifications Dimensions Ceiling mount installation Ceiling mount screw M4 Max L = 25 mm Min L = 20 mm Unit mmWall mount installation Minimum installation requirementsMinimum Ceiling Height mm = f + H + b + 60 + 262.2+ c Timing chart Supported timing for PC inputSupported timing for Hdmi input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsVideo timing Supported 3D signal for Hdmi Hdcp inputPC timing Supported 3D signal for D-SUB input Supported 3D signal for Video and S-Video input Patents Warranty and Copyright informationLimited warranty Copyright