BenQ MX766, MW767, MX822ST user manual Operating the laser pointer, Hdmi, Auto, Mic/Vol +, Mute

Page 15

15.VIDEO

Displays vidoe signal.

16.HDMI

Displays HDMI signal.

17.NETWORK

Enables the network mode.

18.AUTO

Automatically determines the best picture timings for the displayed image. See "Auto-adjusting the image" on page 30 for details.

19.SOURCE

Displays the source selection bar. See "Switching input signal" on page 36 for details.

20.LASER

Emits visible laser pointer light for presentation purposes.

21.MIC/VOL + / -

Adjusts the microphone’s sound level. See for details. See "Adjusting the microphone’s sound level" on page 46 for details.

22.MUTE

Toggles projector audio between on and off. See "Muting the sound" on page 45 for details.

23.ASPECT

Selects the display aspect ratio. See "Selecting the aspect ratio" on page 38 for details.

24.SmartEco

Displays the lamp mode selection bar(Normal/Economic/SmartEco).

Operating the laser pointer

The Laser Pointer is a presentation aid for professionals. It emits red colored light when you press it and the indicator lights up red.

The laser beam is visible. It is necessary to press and hold LASER for continuous output.

Do not look into the laser light window or shine the laser light beam on yourself or others. See the warning messages on the back of the remote control prior to using it.

The laser pointer is not a toy. Parents should be mindful of the dangers of laser energy and keep this remote control out of the reach of children.

Introduction 15

Image 15
Contents MX766/MW767/MX822ST Digital Projector Table of contents Projector lens during operation Important safety instructionsSafety Instructions Do not look straight atSafety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Optional accessories Front/upper side Projector exterior viewMX822ST Rear/lower sideKeystone/Arrow keys / Up Down Volume /Arrow keys / Left, / RightPower/POWER indicator light Controls and functionsMounting the projector Test Remote controlVolume /Arrow keys / Left Right Zoom +MIC/VOL + Operating the laser pointerHdmi AutoReplacing the remote control battery Front Table Set Rear Ceiling in the System Setup BasicPositioning your projector Choosing a locationObtaining a preferred projected image size Max length Inch Max. zoom Min. zoom Projection dimensionsMX766 MW767MX822ST Connection Operation System Minimum Hardware Requirements Connecting a computer Connecting a computer or monitorTo connect the projector to a monitor Connecting a monitorConnecting Video source devices Connecting an Hdmi source deviceTo connect the projector to an Hdmi source device To connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceConnecting with document camera Starting up the projector OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Using build-in test patternMODE/ENTER . The Keystone correction Correcting keystoneLanguage and press Enter to Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordChanging the password Entering the password recall procedureSwitching input signal Disabling the password functionChanging Color Space Magnifying and searching for details About the aspect ratio Selecting the aspect ratioOptimizing the image Selecting a picture modeFine-tuning the image quality in user modes Using Wall ColorSelecting a Color Temperature Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorPress MODE/ENTER and the 3D Color Management page displays To cancel the timer, perform the following steps Setting the presentation timerRemote paging operations Hiding the imageFreezing the image Muting the sound Adjusting the soundAdjusting the sound level Operating in a high altitude environmentTurning off the Power on/off ring tone Adjusting the microphone’s sound levelPersonalizing the projector menu display Until the System Setup Advanced menu is highlighted Select the lamp saver modeUse Teaching Template If you are in a Dhcp environment Configuring the Wired LAN SettingsConfiguring the Wireless LAN Settings Controlling the projector through a LAN environmentControlling the projector remotely through a web browser Through Q Presenter on page 59 for details Page Page Iii Page Page Page Page Displaying image through Q Presenter Iii Iii Vii Using the Projection Login Code Using the Web Control LockPreparation Using the broadcassting functionPresenting From a USB Reader Image File TypesPress Controlling USB ReaderPress Settings Remote Desktop Control through Q Presenter Enter Shutting down the projector PointDraw PenMenu system Menu operationSystem Setup Basic CC1/CC2/CC3/CC4 Dhcp Display menu Description of each menu3D Sync Invert 3D ModePicture menu Picture mode on page 39 for detailsPicture menu Source menu System Setup Basic menu Blank Timer Direct Power OnSignal Power On Auto Power OffSee PointDraw Pen on page 70 for details System Setup Advanced menu Caption Version Closed Caption EnableMicrophone Wired LANWireless LAN NetworkSource System Setup Advanced menu Information menuPicture Mode ResolutionCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode eco function as Economic or SmartEco modeSetting Auto Power Off Lamp informationPage Status Message Timing of replacing the lampReplacing the lamp Page Tighten the screws that secure Lamp Resetting the lamp timerIndicators Light Status & DescriptionLamp events Thermal Sensor 2 open error Thermal Sensor 2 short errorThermal IC #2 I2C Connection error Troubleshooting Specifications Dimensions Ceiling mount screw M4 Max L = 25 mm Min L = 20 mm Unit mm Ceiling mount installationMinimum installation requirements Wall mount installationMinimum Ceiling Height mm = f + H + b + 60 + 262.2+ c Supported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputSupported 3D signal for Hdmi Hdcp input Video timingPC timing Supported 3D signal for D-SUB input Supported 3D signal for Video and S-Video input Copyright Warranty and Copyright informationLimited warranty Patents