BenQ MW767, MX766 System Setup Advanced menu Information menu, Source, Picture Mode, Resolution

Page 85

5. SYSTEM SETUP: Advanced menu

6. INFORMATION menu

	FUNCTION	DESCRIPTION
		AMX Device Discovery
	Network Settings	Selecting On the projector can be detected by AMX controller.
	Network Settings	Mac Address
		Mac Address
		Show Mac address.

		Returns all settings to the factory preset values.
				The following settings will still remain: Position, Phase, H. Size,

				User 1, User 2, Language, Projector Position, High Altitude
				User 1, User 2, Language, Projector Position, High Altitude
				Mode, Security Settings, Baud Rate.
	Reset All Settings

	Source
	Shows the current signal source.
	Picture Mode
	Shows the selected mode in the PICTURE menu.
	Resolution
	Shows the native resolution of the input signal.
	Lamp Mode
Current System	Shows the current lamp mode.
Current System
Status	3D Format
	Shows the current 3D mode.
	Color System
	Shows input system format, NTSC, PAL, SECAM, or RGB.
	Equivalent Lamp
	Displays the number of hours the lamp has been used.
	Firmware Version
	Shows firmware version.

Operation 85

Image 85

Contents MX766/MW767/MX822ST Digital Projector Table of contents Safety Instructions Important safety instructionsDo not look straight at Projector lens during operationSafety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Optional accessories Front/upper side Projector exterior viewMX822ST Rear/lower sidePower/POWER indicator light Volume /Arrow keys / Left, / RightControls and functions Keystone/Arrow keys / Up DownMounting the projector Volume /Arrow keys / Left Right Remote controlZoom + TestHdmi Operating the laser pointerAuto MIC/VOL +Replacing the remote control battery Positioning your projector Set Rear Ceiling in the System Setup BasicChoosing a location Front TableObtaining a preferred projected image size MX766 Projection dimensionsMW767 Max length Inch Max. zoom Min. zoomMX822ST Connection Operation System Minimum Hardware Requirements Connecting a computer Connecting a computer or monitorTo connect the projector to a monitor Connecting a monitorConnecting an Hdmi source device Connecting Video source devicesTo connect the projector to an Hdmi source device To connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceConnecting with document camera Starting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Using build-in test patternMODE/ENTER . The Keystone correction Correcting keystoneLanguage and press Enter to Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signalChanging Color Space Magnifying and searching for details About the aspect ratio Selecting the aspect ratioOptimizing the image Selecting a picture modeFine-tuning the image quality in user modes Using Wall ColorAdjusting Sharpness Adjusting TintAdjusting Brilliant Color Selecting a Color TemperaturePress MODE/ENTER and the 3D Color Management page displays To cancel the timer, perform the following steps Setting the presentation timerHiding the image Remote paging operationsFreezing the image Adjusting the sound level Adjusting the soundOperating in a high altitude environment Muting the soundAdjusting the microphone’s sound level Turning off the Power on/off ring tonePersonalizing the projector menu display Until the System Setup Advanced menu is highlighted Select the lamp saver modeUse Teaching Template Configuring the Wireless LAN Settings Configuring the Wired LAN SettingsControlling the projector through a LAN environment If you are in a Dhcp environmentControlling the projector remotely through a web browser Through Q Presenter on page 59 for details Page Page Iii Page Page Page Page Displaying image through Q Presenter Iii Iii Vii Using the Projection Login Code Using the Web Control LockPresenting From a USB Reader Using the broadcassting functionImage File Types PreparationPress Controlling USB ReaderPress Settings Remote Desktop Control through Q Presenter Enter Shutting down the projector PointDraw PenMenu system Menu operationSystem Setup Basic CC1/CC2/CC3/CC4 Dhcp Display menu Description of each menu3D Sync Invert 3D ModePicture menu Picture mode on page 39 for detailsPicture menu Source menu System Setup Basic menu Signal Power On Direct Power OnAuto Power Off Blank TimerSee PointDraw Pen on page 70 for details System Setup Advanced menu Caption Version Closed Caption EnableWireless LAN Wired LANNetwork MicrophonePicture Mode System Setup Advanced menu Information menuResolution SourceCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode eco function as Economic or SmartEco modeLamp information Getting to know the lamp hourPage Status Message Timing of replacing the lampReplacing the lamp Page Tighten the screws that secure Lamp Resetting the lamp timerLight Status & Description IndicatorsLamp events Thermal Sensor 2 short error Thermal Sensor 2 open errorThermal IC #2 I2C Connection error Troubleshooting Specifications Dimensions Ceiling mount screw M4 Max L = 25 mm Min L = 20 mm Unit mm Ceiling mount installationMinimum installation requirements Wall mount installationMinimum Ceiling Height mm = f + H + b + 60 + 262.2+ c Supported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputVideo timing Supported 3D signal for Hdmi Hdcp inputPC timing Supported 3D signal for D-SUB input Supported 3D signal for Video and S-Video input Limited warranty Warranty and Copyright informationPatents Copyright