BenQ MX822ST, MX766 Warranty and Copyright information, Patents, Limited warranty, Disclaimer

Page 107

Warranty and Copyright information

Patents

This BenQ projector is covered by the following patents:

U.S. patents 6,837,608; 7,275,834; 7,181,318; TW patents 202690; 205470; I228635;

I259932; China Patents (

) ZL01143168.7; ZL03119907.0;

ZL200510051609.2

 

Limited warranty

BenQ warrants this product against any defects in material and workmanship, under normal usage and storage.

Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects.

Important: The above warranty shall be void if the customer fails to operate the product in accordance with BenQ's written instructions, especially the ambient humidity must be in- between 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920 feet, and avoiding to operate the projector in a dusty environment. This warranty gives you specific legal rights, and you may have other rights which vary from country to country.

For other information, please visit www.BenQ.com.

Copyright

Copyright 2012 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.

Disclaimer

BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others are copyrights of their respective companies or organizations.

Warranty and Copyright information 107

Image 107
Contents MX766/MW767/MX822ST Digital Projector Table of contents Projector lens during operation Important safety instructionsSafety Instructions Do not look straight atSafety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Optional accessories Front/upper side Projector exterior viewMX822ST Rear/lower sideKeystone/Arrow keys / Up Down Volume /Arrow keys / Left, / RightPower/POWER indicator light Controls and functionsMounting the projector Test Remote controlVolume /Arrow keys / Left Right Zoom +MIC/VOL + Operating the laser pointerHdmi AutoReplacing the remote control battery Front Table Set Rear Ceiling in the System Setup BasicPositioning your projector Choosing a locationObtaining a preferred projected image size Max length Inch Max. zoom Min. zoom Projection dimensionsMX766 MW767MX822ST Connection Operation System Minimum Hardware Requirements Connecting a computer Connecting a computer or monitorTo connect the projector to a monitor Connecting a monitorTo connect the projector to an Hdmi source device Connecting Video source devicesConnecting an Hdmi source device To connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceConnecting with document camera Starting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Using build-in test patternMODE/ENTER . The Keystone correction Correcting keystoneLanguage and press Enter to Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordChanging the password Entering the password recall procedureChanging Color Space Switching input signalDisabling the password function Magnifying and searching for details About the aspect ratio Selecting the aspect ratioOptimizing the image Selecting a picture modeFine-tuning the image quality in user modes Using Wall ColorSelecting a Color Temperature Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorPress MODE/ENTER and the 3D Color Management page displays To cancel the timer, perform the following steps Setting the presentation timerFreezing the image Remote paging operationsHiding the image Muting the sound Adjusting the soundAdjusting the sound level Operating in a high altitude environmentPersonalizing the projector menu display Turning off the Power on/off ring toneAdjusting the microphone’s sound level Until the System Setup Advanced menu is highlighted Select the lamp saver modeUse Teaching Template If you are in a Dhcp environment Configuring the Wired LAN SettingsConfiguring the Wireless LAN Settings Controlling the projector through a LAN environmentControlling the projector remotely through a web browser Through Q Presenter on page 59 for details Page Page Iii Page Page Page Page Displaying image through Q Presenter Iii Iii Vii Using the Projection Login Code Using the Web Control LockPreparation Using the broadcassting functionPresenting From a USB Reader Image File TypesPress Controlling USB ReaderPress Settings Remote Desktop Control through Q Presenter Enter Shutting down the projector PointDraw PenMenu system Menu operationSystem Setup Basic CC1/CC2/CC3/CC4 Dhcp Display menu Description of each menu3D Sync Invert 3D ModePicture menu Picture mode on page 39 for detailsPicture menu Source menu System Setup Basic menu Blank Timer Direct Power OnSignal Power On Auto Power OffSee PointDraw Pen on page 70 for details System Setup Advanced menu Caption Version Closed Caption EnableMicrophone Wired LANWireless LAN NetworkSource System Setup Advanced menu Information menuPicture Mode ResolutionCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode eco function as Economic or SmartEco modeSetting Auto Power Off Lamp informationPage Status Message Timing of replacing the lampReplacing the lamp Page Tighten the screws that secure Lamp Resetting the lamp timerLamp events IndicatorsLight Status & Description Thermal IC #2 I2C Connection error Thermal Sensor 2 open errorThermal Sensor 2 short error Troubleshooting Specifications Dimensions Ceiling mount screw M4 Max L = 25 mm Min L = 20 mm Unit mm Ceiling mount installationMinimum installation requirements Wall mount installationMinimum Ceiling Height mm = f + H + b + 60 + 262.2+ c Supported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputPC timing Supported 3D signal for Hdmi Hdcp inputVideo timing Supported 3D signal for D-SUB input Supported 3D signal for Video and S-Video input Copyright Warranty and Copyright informationLimited warranty Patents