BenQ MX822ST, MX766, MW767 user manual Closed Caption Enable, Caption Version

Page 83

5. SYSTEM SETUP: Advanced menu

FUNCTION

DESCRIPTION

 

Selecting On enables the function and the projector displays the grid

Test Pattern

test pattern. It helps you adjust the image size and focus and check

that the projected image is free from distortion. See "Using build-in

 

 

test pattern" on page 31 for details.

 

Closed Caption Enable

 

Activates the function by selecting On when the selected input signal

 

carries closed captions.

 

• Captions: An on-screen display of the dialogue, narration, and

 

 

sound effects of TV programs and videos that are closed

 

 

captioned (usually marked as "CC" in TV listings).

 

 

 

Set your screen aspect ratio to 4:3. This function is not available

 

 

 

Closed Caption

 

 

when the aspect ratio is “16:9”, “16:10” or “Real”.

 

 

 

Caption Version

 

Selects a preferred closed captioning mode. To view captions, select

 

CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary

 

language in your area).

Operation 83

Image 83
Contents MX766/MW767/MX822ST Digital Projector Table of contents Projector lens during operation Important safety instructionsSafety Instructions Do not look straight atSafety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Optional accessories Front/upper side Projector exterior viewMX822ST Rear/lower sideKeystone/Arrow keys / Up Down Volume /Arrow keys / Left, / RightPower/POWER indicator light Controls and functionsMounting the projector Test Remote controlVolume /Arrow keys / Left Right Zoom +MIC/VOL + Operating the laser pointerHdmi AutoReplacing the remote control battery Front Table Set Rear Ceiling in the System Setup BasicPositioning your projector Choosing a locationObtaining a preferred projected image size Max length Inch Max. zoom Min. zoom Projection dimensionsMX766 MW767MX822ST Connection Operation System Minimum Hardware Requirements Connecting a computer Connecting a computer or monitorTo connect the projector to a monitor Connecting a monitorTo connect the projector to an Hdmi source device Connecting Video source devicesConnecting an Hdmi source device To connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceConnecting with document camera Starting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Using build-in test patternMODE/ENTER . The Keystone correction Correcting keystoneLanguage and press Enter to Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordChanging the password Entering the password recall procedureChanging Color Space Switching input signalDisabling the password function Magnifying and searching for details About the aspect ratio Selecting the aspect ratioOptimizing the image Selecting a picture modeFine-tuning the image quality in user modes Using Wall ColorSelecting a Color Temperature Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorPress MODE/ENTER and the 3D Color Management page displays To cancel the timer, perform the following steps Setting the presentation timerFreezing the image Remote paging operationsHiding the image Muting the sound Adjusting the soundAdjusting the sound level Operating in a high altitude environmentPersonalizing the projector menu display Turning off the Power on/off ring toneAdjusting the microphone’s sound level Until the System Setup Advanced menu is highlighted Select the lamp saver modeUse Teaching Template If you are in a Dhcp environment Configuring the Wired LAN SettingsConfiguring the Wireless LAN Settings Controlling the projector through a LAN environmentControlling the projector remotely through a web browser Through Q Presenter on page 59 for details Page Page Iii Page Page Page Page Displaying image through Q Presenter Iii Iii Vii Using the Projection Login Code Using the Web Control LockPreparation Using the broadcassting functionPresenting From a USB Reader Image File TypesPress Controlling USB ReaderPress Settings Remote Desktop Control through Q Presenter Enter Shutting down the projector PointDraw PenMenu system Menu operationSystem Setup Basic CC1/CC2/CC3/CC4 Dhcp Display menu Description of each menu3D Sync Invert 3D ModePicture menu Picture mode on page 39 for detailsPicture menu Source menu System Setup Basic menu Blank Timer Direct Power OnSignal Power On Auto Power OffSee PointDraw Pen on page 70 for details System Setup Advanced menu Caption Version Closed Caption EnableMicrophone Wired LANWireless LAN NetworkSource System Setup Advanced menu Information menuPicture Mode ResolutionCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode eco function as Economic or SmartEco modeSetting Auto Power Off Lamp informationPage Status Message Timing of replacing the lampReplacing the lamp Page Tighten the screws that secure Lamp Resetting the lamp timerLamp events IndicatorsLight Status & Description Thermal IC #2 I2C Connection error Thermal Sensor 2 open errorThermal Sensor 2 short error Troubleshooting Specifications Dimensions Ceiling mount screw M4 Max L = 25 mm Min L = 20 mm Unit mm Ceiling mount installationMinimum installation requirements Wall mount installationMinimum Ceiling Height mm = f + H + b + 60 + 262.2+ c Supported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputPC timing Supported 3D signal for Hdmi Hdcp inputVideo timing Supported 3D signal for D-SUB input Supported 3D signal for Video and S-Video input Copyright Warranty and Copyright informationLimited warranty Patents