BenQ MW767, MX766, MX822ST user manual CC1/CC2/CC3/CC4

Page 73

5. SYSTEM SETUP: Advanced

	High Altitude	On/Off	Yes/No
	Mode	On/Off	Yes/No
	Mode

		Mute	On/Off

		Volume	0~10

	Audio Settings	Microphone	0~10
		Volume
		Power on/off Ring	On/Off
		Tone
		Lamp Mode	Normal/Economic/SmartEco
	Lamp Settings
	Lamp Settings	Reset lamp timer	Reset/Cancel

		Equivalent lamp

	Security	Change password

			Power on Lock
	Settings	Change Security	Power on Lock

			Web Control Lock
			Web Control Lock

	Baud Rate		2400/4800/9600/14400/19200/
	Baud Rate		38400/57600/115200
			38400/57600/115200

	Test Pattern		On/Off

		Closed Caption	On/Off
	Closed Caption	Enable	On/Off
	Closed Caption	Enable
		Caption Version	CC1/CC2/CC3/CC4

		Network	On/Off

	Standby	Microphone	On/Off

		Monitor Out	On/Off
	Settings	Monitor Out	On/Off
	Settings
		Audio Pass	Off /Computer 1/Computer 2/
		Through	Video, Svideo/HDMI

Operation 73

Image 73

Contents MX766/MW767/MX822ST Digital Projector Table of contents Safety Instructions Important safety instructionsDo not look straight at Projector lens during operationSafety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Optional accessories Front/upper side Projector exterior viewMX822ST Rear/lower sidePower/POWER indicator light Volume /Arrow keys / Left, / RightControls and functions Keystone/Arrow keys / Up DownMounting the projector Volume /Arrow keys / Left Right Remote controlZoom + TestHdmi Operating the laser pointerAuto MIC/VOL +Replacing the remote control battery Positioning your projector Set Rear Ceiling in the System Setup BasicChoosing a location Front TableObtaining a preferred projected image size MX766 Projection dimensionsMW767 Max length Inch Max. zoom Min. zoomMX822ST Connection Operation System Minimum Hardware Requirements Connecting a computer Connecting a computer or monitorTo connect the projector to a monitor Connecting a monitorConnecting an Hdmi source device Connecting Video source devicesTo connect the projector to an Hdmi source device To connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceConnecting with document camera Starting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Using build-in test patternMODE/ENTER . The Keystone correction Correcting keystoneLanguage and press Enter to Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signalChanging Color Space Magnifying and searching for details About the aspect ratio Selecting the aspect ratioOptimizing the image Selecting a picture modeFine-tuning the image quality in user modes Using Wall ColorAdjusting Sharpness Adjusting TintAdjusting Brilliant Color Selecting a Color TemperaturePress MODE/ENTER and the 3D Color Management page displays To cancel the timer, perform the following steps Setting the presentation timerHiding the image Remote paging operationsFreezing the image Adjusting the sound level Adjusting the soundOperating in a high altitude environment Muting the soundAdjusting the microphone’s sound level Turning off the Power on/off ring tonePersonalizing the projector menu display Until the System Setup Advanced menu is highlighted Select the lamp saver modeUse Teaching Template Configuring the Wireless LAN Settings Configuring the Wired LAN SettingsControlling the projector through a LAN environment If you are in a Dhcp environmentControlling the projector remotely through a web browser Through Q Presenter on page 59 for details Page Page Iii Page Page Page Page Displaying image through Q Presenter Iii Iii Vii Using the Projection Login Code Using the Web Control LockPresenting From a USB Reader Using the broadcassting functionImage File Types PreparationPress Controlling USB ReaderPress Settings Remote Desktop Control through Q Presenter Enter Shutting down the projector PointDraw PenMenu system Menu operationSystem Setup Basic CC1/CC2/CC3/CC4 Dhcp Display menu Description of each menu3D Sync Invert 3D ModePicture menu Picture mode on page 39 for detailsPicture menu Source menu System Setup Basic menu Signal Power On Direct Power OnAuto Power Off Blank TimerSee PointDraw Pen on page 70 for details System Setup Advanced menu Caption Version Closed Caption EnableWireless LAN Wired LANNetwork MicrophonePicture Mode System Setup Advanced menu Information menuResolution SourceCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode eco function as Economic or SmartEco modeLamp information Getting to know the lamp hourPage Status Message Timing of replacing the lampReplacing the lamp Page Tighten the screws that secure Lamp Resetting the lamp timerLight Status & Description IndicatorsLamp events Thermal Sensor 2 short error Thermal Sensor 2 open errorThermal IC #2 I2C Connection error Troubleshooting Specifications Dimensions Ceiling mount screw M4 Max L = 25 mm Min L = 20 mm Unit mm Ceiling mount installationMinimum installation requirements Wall mount installationMinimum Ceiling Height mm = f + H + b + 60 + 262.2+ c Supported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputVideo timing Supported 3D signal for Hdmi Hdcp inputPC timing Supported 3D signal for D-SUB input Supported 3D signal for Video and S-Video input Limited warranty Warranty and Copyright informationPatents Copyright