BenQ PB8263 user manual Supported timing for Component-YPbPrinput

Page 59

Supported timing for Component-YPbPrinput

	Signal Format	Horizontal Frequency	Vertical Frequency
	Signal Format	(kHz)	(Hz)
		(kHz)	(Hz)

	480i(525i)@60Hz	15.73	59.94
	480p(525p)@60Hz	31.47	59.94
	576i(625i)@50Hz	15.63	50.00
	576p(625p)@50Hz	31.25	50.00
	720p(750p)@60Hz	45.00	60.00
	720p(750p)@50Hz	37.50	50.00
	1080i(1125i)@60Hz	33.75	60.00
	1080i(1125i)@50Hz	28.13	50.00

Supported timing for Video and S-Video inputs

	Video mode	Horizontal	Vertical	Color Sub-carrier
	Video mode	Frequency (kHz)	Frequency (Hz)	Frequency (MHz)
		Frequency (kHz)	Frequency (Hz)	Frequency (MHz)

	NTSC	15.73	60	3.58

	PAL	15.63	50	4.43

	SECAM	15.63	50	4.25 or 4.41

	PAL-M	15.73	60	3.58

	PAL-N	15.63	50	3.58

	PAL-60	15.73	60	4.43

	NTSC4.43	15.73	60	4.43

Specifications 59

Image 59

Contents Welcome Disclaimer CopyrightTable of contents Temperature information Safety Instructions Important safety instructionsSafety Instructions Allow at least 50 cm clearance from walls Locations near fire alarmsLocations with an ambient temperature Bedding or any other soft surfaceSafety Instructions Introduction Projector featuresIntroduction Shipping contents Lower view Projector exterior viewFront/upper side Rear/side viewConnector panel Projector Controls and functionsRemote control Mode LED indicator lightVolume + PIP POSRemote control batteries Remote control effective rangeChoosing a location Positioning your projectorSafety instructions for ceiling mounting of the projector Obtaining a preferred projected image size Page 1500 Maximum zoom Minimum zoomScreen Center of lens Projection distance 1219Connection Connecting a computer or monitorConnecting a computer Connection VGA to DVI-A Connecting a monitorWith a VGA cable With a VGA to DVI-A cable Better video quality Connecting Video source devicesConnecting Audio Best video qualityMute on page 45 for details Connecting a DVI source device1080i 50/ 60 Hz Connecting a Component Video source deviceConnecting an S-Video source device Connecting a composite Video source device Start up Power onOperation Adjusting the projection angle Switching input signalAdjusting the projected image Searching for details on the image Auto-adjusting the imageFine-tuning the image size and clarity Any problems?Scales an image so that it is displayed in the center Selecting the aspect ratioFor example Optimizing the imageCorrecting keystone YPbPr/YCbCr/DVI-D/S-Video/Video Signal Input Selecting a preset modePC/DVI-A Signal Input Selecting a color temperature Other adjustmentsAdjusting brightness Adjusting contrastPersonalizing the projector menu display Operating in a high altitude environmentFreezing the image Using the laser pointer in the presentationHiding the image Remote paging operationsOperation in the OSD menus Operation on the remote controlPIP Picture In Picture operation Shutting down the projector OSD menu system On-Screen Display OSD menu operationDisplay menu Using the menusPressing Left/ Right on the projector or remote control Display menu Image menu Treble VolumeSource menu MirrorControl menu PIP menu Care of the projector MaintenanceRear filter Access to the rear dust filter is located on the left sideFront filter Lamp information Use and replacement of the lampReplacing the lamp Reset lamp hours and press Exit to leave Temperature informationRe-install the lamp cover and tighten the screws Projector is under normal operation IndicatorsStand-by mode IllustrationPower Temp Lamp Thermal events No picture TroubleshootingRemote control does not work Projector does not turn onRemote mouse function does not work Projector specifications SpecificationsSupported timing for PC including DVI-I input DimensionsTiming chart Horizontal Vertical Pixel Resolution Frequency Mode KHz MHzSupported timing for Video and S-Video inputs Signal Format Horizontal Frequency Vertical Frequency KHzSupported timing for Component-YPbPrinput Limited Warranty WarrantyMIC statement Regulation StatementsFCC statement EEC statement