Mitsubishi Electronics HC7800DW user manual Risk of Electric Shock Do not Open

Page 2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NOTE:

SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.

WARNING

Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception.

This apparatus must be grounded.

DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE.

CAUTION

The attached power cord is to be used exclusively for this product. Never use it for other products.

EN-2

Image 2
Contents HC7800D Risk of Electric Shock Do not Open Contents Important safeguards Important safeguards Preparing your projector Inserting the batteries into the remote controlRemoving the batteries from the remote control What’s included in the boxControl panel Preparing your projectorOverview Picture quality selection buttons Remote controlPicture quality adjusting buttons Reception angle Using the remote controlOperational range of the remote control When the aspect ratio of the screen is Setting up your projectorSetting up the screen Screen size and projection distanceWhen the aspect ratio of the image is Setting up your projectorWhen the aspect ratio of the screen is 2.351 CinemaScope When projected images are distorted to a trapezoid Adjusting the position of the projected imageWhen fine streaks are seen on projected images Correcting skewed or distorted imageRear projection Front projection, ceiling mountingTrigger terminal Basic home theater system connection Connecting the projector to video equipmentViewing video images PreparationConnecting to a DVD player or Hdtv decoder Viewing video imagesConnecting to video equipment having a Hdmi terminal Connection for video equipment having an Hdmi terminalPlugging in the power cord Projecting images To stop projecting Setting the aspect ratio ZOOM1 ZOOM2 Stretch ANAMORPHIC1 ANAMORPHIC2How to change the settings With the remote controlViewing computer images Connecting the projector to a computerPlugging the power cord About DDCViewing computer images ComputerExample of the setting procedure for external output When connecting to a notebook computerSetting of the resolution Auto Position buttonInstalling the 3D emitter Viewing 3D images3D images viewing To change the 3D viewing modeViewing 3D images To view 3D imagesEN-27 You can make various settings using the displayed menus Menu operationPress the Menu button How to set the menusMenu operation Menu selection bar is displayedMenu items Image menuScreen Size Setting Function Advanced MenuSetup Auto Vertical LocationInstallation menu Feature menu Signal menu Network menu AV memory Adjusting projected imagesInformation menu To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessTo enable the stored color temperature To adjust the tone of white Color TempAbout color temperature To optically brighten or darken projected images Auto IrisTo use Color Management To adjust the ratio of change in brightness Gamma ModeTo enable the stored gamma mode BLUEMAGENTAREDTo adjust the vertical position LPF Progressive filterTo enable the password function Advanced featuresPassword function To cancel the password functionAdvanced features Major functionsPJLink supported commands ConnectionNetwork password settings Initial network settingsSetting projector name Setting or clearing Dhcp Initial network settingsIP settings IP address settingsDefault gateway settings Initialization of network settingsSubnet mask settings Enabling or disabling the PJLink certificationDhcp How to use network functionGlossary Interval of lamp replacement Replacing the lampWhen the projector is mounted to the ceiling Replacing the lampReset of the lamp operation time Cleaning of the lens MaintenanceCleaning of the projector and the ventilation slots Troubleshooting No image appears on the screen ProblemImages are not displayed correctly Problem Solution TroubleshootingNo image appears on the screen Problem Solution Others Problem Solution EN-55 EN-56 Condition Possible Solution IndicatorsPower Status Condition Normal conditionSpecifications Dimension drawings unit mmSpecifications 3D supported signalsCOMPUTER/COMPONENT Video Hdmi 1, Hdmi ConnectorsReplacement part option/not included in the box VLT-HC7800LPZusho Baba, Nagaokakyo-City, Kyoto Japan