Mitsubishi Electronics HC7800DW user manual Replacing the lamp, Interval of lamp replacement

Page 48

Replacing the lamp

This projector is equipped with a lamp to project images. This lamp is a consumable. It may burn out or its brightness may decrease during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new lamp sold separately that is exclusive to this projector. Contact your dealer for purchase of the lamp.

Spare lamp VLT-HC7800LP

Warning:

•Be careful not to drop the lamp fixing screws inside of the projector. Don’t put a metal piece or flammable object into the projector. Using the projector with any foreign object present inside may result in electric shock or fire. When you can’t remove the foreign object from the inside, contact your dealer for removal.

•Do not touch the lamp with bare hands or give a shock to the lamp. Attach the lamp properly. Improper handling may cause explosion.

•Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. Improper installation may also result in fire.

•Don’t shake the removed lamp or don’t lift it above your face. Your eyes may be injured by flying or falling glass fragments.

•Don’t replace the lamp immediately after use because the lamp cover will be very hot. You may get burned. Turn off the power using the POWER button. After the lamp goes out, wait about two minutes until the intake and exhaust fans for cooling the lamp stop rotating. Then unplug the power cord, and wait at least one hour to allow the lamp to cool down enough to the touch.

Interval of lamp replacement

The recommended interval of lamp replacement is about 5000 hours*1*2 of consecutive use. Such interval differs depending on the operating environment and may be shorter than 5000 hours*1*2. Decrease in luminescence and/or color brightness indicates that the lamp needs to be replaced. When the lamp operation time exceeds 3750 hours*1, the indicator will blink alternately between green and red (while the lamp is lit; when the lamp is not lit, the indicator will be lit red only) and the lamp replacement message will appear on the screen for one minute everytime the lamp is turned on. When the lamp has been used for about 4750 hours*1, the replacement message (LAMP REPLACEMENT) will appear on the screen for one minute every 25 hours*1 thereafter. When the lamp operation time exceeds 5000 hours*1*2, the projector automatically shuts off and can’t be used until the lamp is replaced and the lamp operation time is reset.

*1: Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be shorted.

*2: When LAMP MODE is set to STANDARD, this duration will be shorted to 3000 hours.

Caution:

•Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a breakdown.

•This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may explode or fail to illuminate permanently because of an impact, scratch, or deterioration through use. The period of time until explosion or permanent failure to illuminate varies considerably from lamp to lamp, depending on operation conditions. Therefore, the lamp may explode soon after the start of use.

•The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the instruction of lamp replacement appears, replace it with a new one immediately even if the lamp is still lighting normally.

•When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and the gas charged inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains mercury. Be careful not to breathe it or avoid it from entering your eye or mouth. If you should breathe it or if it should enter your eye or mouth, see a doctor immediately.

•In the event that the high-pressure mercury lamp exploded, glass fragments may have been scattered inside the projector. Ask your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace the lamp by yourself, be sure to hold the handle of the lamp. You may get injured by glass fragments.

•When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the projector or option lamp to prevent glass fragments from scattering.

•Be sure to use the lamp exclusive to this projector, VLT-HC7800LP. Use of other lamps may cause a failure of the projector.

EN-48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents HC7800D Risk of Electric Shock Do not Open Contents Important safeguards Important safeguards Inserting the batteries into the remote control Removing the batteries from the remote controlPreparing your projector What’s included in the boxPreparing your projector OverviewControl panel Remote control Picture quality adjusting buttonsPicture quality selection buttons Using the remote control Operational range of the remote controlReception angle Setting up your projector Setting up the screenWhen the aspect ratio of the screen is Screen size and projection distanceSetting up your projector When the aspect ratio of the screen is 2.351 CinemaScopeWhen the aspect ratio of the image is Adjusting the position of the projected image When fine streaks are seen on projected imagesWhen projected images are distorted to a trapezoid Correcting skewed or distorted imageFront projection, ceiling mounting Trigger terminalRear projection Connecting the projector to video equipment Viewing video imagesBasic home theater system connection PreparationConnecting to a DVD player or Hdtv decoder Viewing video imagesConnecting to video equipment having a Hdmi terminal Connection for video equipment having an Hdmi terminalPlugging in the power cord Projecting images To stop projecting Setting the aspect ratio ZOOM1 ZOOM2 Stretch ANAMORPHIC1 ANAMORPHIC2How to change the settings With the remote controlConnecting the projector to a computer Plugging the power cordViewing computer images About DDCViewing computer images ComputerWhen connecting to a notebook computer Setting of the resolutionExample of the setting procedure for external output Auto Position buttonInstalling the 3D emitter Viewing 3D imagesTo change the 3D viewing mode Viewing 3D images3D images viewing To view 3D imagesEN-27 You can make various settings using the displayed menus Menu operationHow to set the menus Menu operationPress the Menu button Menu selection bar is displayedMenu items Image menuSetting Function Advanced Menu Setup AutoScreen Size Vertical LocationInstallation menu Feature menu Signal menu Network menu Adjusting projected images Information menuAV memory Adjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessTo adjust the tone of white Color Temp About color temperatureTo enable the stored color temperature To optically brighten or darken projected images Auto IrisTo adjust the ratio of change in brightness Gamma Mode To enable the stored gamma modeTo use Color Management BLUEMAGENTAREDTo adjust the vertical position LPF Progressive filterAdvanced features Password functionTo enable the password function To cancel the password functionAdvanced features Major functionsPJLink supported commands ConnectionInitial network settings Setting projector nameNetwork password settings Initial network settings IP settingsSetting or clearing Dhcp IP address settingsInitialization of network settings Subnet mask settingsDefault gateway settings Enabling or disabling the PJLink certificationHow to use network function GlossaryDhcp Interval of lamp replacement Replacing the lampWhen the projector is mounted to the ceiling Replacing the lampReset of the lamp operation time Maintenance Cleaning of the projector and the ventilation slotsCleaning of the lens Troubleshooting No image appears on the screen ProblemTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly Problem Solution Others Problem Solution EN-55 EN-56 Indicators Power Status ConditionCondition Possible Solution Normal conditionSpecifications Dimension drawings unit mmSpecifications 3D supported signalsConnectors Replacement part option/not included in the boxCOMPUTER/COMPONENT Video Hdmi 1, Hdmi VLT-HC7800LPZusho Baba, Nagaokakyo-City, Kyoto Japan
Top Page Image Contents