Mitsubishi Electronics HC7800DW user manual EN-27

Page 27

Viewing 3D images (continued)

Important:

If the viewing distance is nearer than the recommended distance, it will cause physical discomfort and eye fatigue.

The 3D glasses may not work properly when it is used too far from the screen.

Watch the contents in front of the screen, not at big angle. If you are viewing the screen at big angle, you may not be able to view 3D contents correctly.

There are personal differences in viewing the 3D images. For persons with myopia, hypermetropia, astigmatism or left and right sights, please wear glasses to correct them then wear the 3D glasses.

The picture seems misplaced at the start of projecting the 3D images, however, this is not a malfunction.

When 3D in the IMAGE menu is set to OFF, 3D images are not displayed properly.

While side-by-side or top-and-bottom 3D images are displayed, the aspect ratio setting is fixed to 16:9.

When you display a menu or dialog while viewing side-by-side or top-and-bottom 3D images, they are displayed in the 2D mode temporarily. When the menu or dialog disappears, they are displayed in the 3D mode again.

The keystone setting is invalid (restored to the default setting) while you are watching the 3D images. The setting can not be changed.

When connecting the projector and a player such as BD player through a HDMI signal distributor or AV amplifier via HDMI cable, make sure to use the HDMI signal distributor or AV amplifier supporting HDMI 1.4 (3D).

This projector controls the open/close timing of the 3D glasses lenses (liquid crystal shutter) by using the infra-red signals received from the 3D emitter. Therefore, in rare cases, a remote control of other devices such as an air conditioner or lighting apparatus which uses the infra-red signals may not operate properly (while you are watching the 3D images). However, it is not a malfunction.

Caution:

Notes on danger to public health during watching 3D image

Stop viewing the 3D image immediately if you feel tired, discomfort, or any other abnormality. It may cause you to feel unwell if continuing to watch the 3D image in such cases. Please take the necessary rest, do not continue watch the 3D image for a long time. Stop using the 3D glasses if you can clearly see double images when viewing 3D content. Prolonged use may cause eyesight fatigue.

The following people need to refrain from use as with 2D image.

a photosensitive patient

a patient with heart disease

a person in poor physical condition

a sleepy person

a very tired person

a drunk person

children

When watching 3D movies, take an appropriate break after watching a movie. When watching 3D content on interactive devices such as 3D games or computers, take an appropriate break every

30-60 minutes. Prolonged use may cause eyesight fatigue.

When you feel uncomfortable, stop viewing

3D images and playing 3D games until you are restored. If necessary, consult a doctor. Also, stop driving a car until you are restored (for about 2 hours). The period to restore varies with the individual.

As a guide, 3D glasses should not be used by children younger than 5 - 6 years old. As it is difficult to judge younger children’s reactions to fatigue or discomfort, their physical condition may deteriorate suddenly. When this product is being used by a child, the parent or guardian should check to ensure that the child’s eyes are not becoming tired.

When viewing the pictures that roll over and shake or many dynamic pictures, if you feel uncomfortable, please look at another place.

When viewing contents with movements such as rotation, or horizontal or vertical oscillation, you may feel as if you are actually moving. If such a feeling results in discomfort, look away from the screen.

When using the 3D glasses, be careful not to strike the screen or other people by mistake. As the images are in 3D, you may mistake the distance from the screen, causing to strike the screen which may result in injury. When using the 3D glasses, do not place breakable objects near the glasses. You may move by mistaking the 3D objects you are viewing as the real objects, causing damages to surrounding objects that may lead to injury.

When using the 3D glasses, make sure your eyes are on an approximate horizontal level. If you suffer from myopia (short sightedness), hyperopia (far-sightedness), astigmatism, or have eyesight differences between the left and right eyes, please use corrective glasses or other such methods to correct your eyesight before putting on the 3D glasses.

When you view the 3D images, keep a distance from the screen of about three times the effective height of the screen.

EN-27

Image 27
Contents HC7800D Risk of Electric Shock Do not Open Contents Important safeguards Important safeguards What’s included in the box Inserting the batteries into the remote controlRemoving the batteries from the remote control Preparing your projectorPreparing your projector OverviewControl panel Remote control Picture quality adjusting buttonsPicture quality selection buttons Using the remote control Operational range of the remote controlReception angle Screen size and projection distance Setting up your projectorSetting up the screen When the aspect ratio of the screen isSetting up your projector When the aspect ratio of the screen is 2.351 CinemaScopeWhen the aspect ratio of the image is Correcting skewed or distorted image Adjusting the position of the projected imageWhen fine streaks are seen on projected images When projected images are distorted to a trapezoidFront projection, ceiling mounting Trigger terminalRear projection Preparation Connecting the projector to video equipmentViewing video images Basic home theater system connectionViewing video images Connecting to a DVD player or Hdtv decoderConnection for video equipment having an Hdmi terminal Connecting to video equipment having a Hdmi terminalPlugging in the power cord Projecting images To stop projecting ZOOM1 ZOOM2 Stretch ANAMORPHIC1 ANAMORPHIC2 Setting the aspect ratioWith the remote control How to change the settingsAbout DDC Connecting the projector to a computerPlugging the power cord Viewing computer imagesComputer Viewing computer imagesAuto Position button When connecting to a notebook computerSetting of the resolution Example of the setting procedure for external outputViewing 3D images Installing the 3D emitterTo view 3D images To change the 3D viewing modeViewing 3D images 3D images viewingEN-27 Menu operation You can make various settings using the displayed menusMenu selection bar is displayed How to set the menusMenu operation Press the Menu buttonImage menu Menu itemsVertical Location Setting Function Advanced MenuSetup Auto Screen SizeInstallation menu Feature menu Signal menu Network menu Adjusting projected images Information menuAV memory To sharpen or soften the projected image Sharpness Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintTo optically brighten or darken projected images Auto Iris To adjust the tone of white Color TempAbout color temperature To enable the stored color temperatureBLUEMAGENTARED To adjust the ratio of change in brightness Gamma ModeTo enable the stored gamma mode To use Color ManagementLPF Progressive filter To adjust the vertical positionTo cancel the password function Advanced featuresPassword function To enable the password functionMajor functions Advanced featuresConnection PJLink supported commandsInitial network settings Setting projector nameNetwork password settings IP address settings Initial network settingsIP settings Setting or clearing DhcpEnabling or disabling the PJLink certification Initialization of network settingsSubnet mask settings Default gateway settingsHow to use network function GlossaryDhcp Replacing the lamp Interval of lamp replacementReplacing the lamp When the projector is mounted to the ceilingReset of the lamp operation time Maintenance Cleaning of the projector and the ventilation slotsCleaning of the lens No image appears on the screen Problem TroubleshootingTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly Problem Solution Others Problem Solution EN-55 EN-56 Normal condition IndicatorsPower Status Condition Condition Possible SolutionDimension drawings unit mm Specifications3D supported signals SpecificationsVLT-HC7800LP ConnectorsReplacement part option/not included in the box COMPUTER/COMPONENT Video Hdmi 1, HdmiZusho Baba, Nagaokakyo-City, Kyoto Japan