Mitsubishi Electronics HC7800DW user manual Menu operation

Menu operation

You can make various settings using the displayed menus.

IMAGE

PICTURE MODE	CINEMA, VIDEO, 3D, ISF(DAY), ISF(NIGHT),
	AV MEMORY1	, AV MEMORY2 , AV MEMORY3

GAMMA MODE	CINEMA, 2.0, 2.1(VIDEO), 2.2, 3D, 2.4
	USER1	, USER2
CONTRAST	±30
BRIGHTNESS	±30
COLOR TEMP.	HIGH BRIGHTNESS, COOL, MEDIUM, WARM, 3D
	USER

REFERENCE

ADJUST MODE

2%, 4%, 6%, 10%, 15%, 20%, 25%, 30%, 40%, 50%, 70%, 90%

REFERENCE

CONTRAST R

CONTRAST G

CONTRAST B

BRIGHTNESS R

BRIGHTNESS G

BRIGHTNESS B

2.0, 2.1(VIDEO), 2.2, 3D, 2.4
ALL, RED, GREEN, BLUE
±99 (R)	±99 (G)	±99 (B)
COOL, MEDIUM, WARM
±60
±60
±60
±60
±60
±60

COLOR

TINT

SHARPNESS *1

BrilliantColor™

3D

ADVANCED MENU

±10

±10

±5

ON, OFF

ON

OFF

OK

3D MODE	AUTO, FRAME PACKING, SIDE BY SIDE, TOP AND BOTTOM
3D SYNC.	NORMAL, REVERSE
2D-3D CONVERSION	ON, OFF
3D DEPTH	1 - 10

SCREEN SIZE		16:9, CINEMA SCOPE (2.35:1)
VERTICAL LOCATION		±26
FRAME RATE CONVERSION		OFF, TRUE FILM, TRUE VIDEO
F.R.C. LEVEL		1 - 5
AUTO IRIS		OFF, AUTO 1, AUTO 2, AUTO 3
NOISE REDUCTION*6		ON, OFF
CTI	*1	0 - 5
HDMI INPUT		AUTO, ENHANCED, NORMAL, SUPERWHITE	*7
SETUP	*1	AUTO, OFF, 3.75%, 7.5%
COLOR MANAGEMENT		ON
		OFF
COLOR SPACE		WIDE, NORMAL

INSTALLATION

KEYSTONE

LAMP MODE

STANDBY MODE

AUTO POWER ON

AUTO POWER OFF

SPLASH SCREEN

BACK COLOR

IMAGE REVERSE

TRIGGER1(POWER)

TRIGGER2(ANAMO)

TEST PATTERN

		COLOR
		GAIN
		SATURATION
±15		HUE
		POSITION
STANDARD, LOW
		FULL/MONO
STANDARD, LOW
		RESET
ON, OFF
OFF, 5 min, 10 min, 15 min, 30 min, 60 min
ON, OFF
BLUE, BLACK
OFF, MIRROR, INVERT, MIRROR INVERT
ON, OFF
ON, OFF
CROSS HATCH	, WHITE	, BLACK

RED, YELLOW, GREEN, CYAN, BLUE, MAGENTA

-49 - 50

±50

±50

RIGHT UP, LEFT DOWN

FULL COLOR, MONO COLOR

OK

FEATURE

ASPECT	AUTO, 4:3, 16:9, ZOOM1, ZOOM2, STRETCH, ANAMORPHIC1, ANAMORPHIC2 *3
PASSWORD FUNCTION	DISPLAY INPUT	, MENU ACCESS	LOCK			OK
MENU POSITION	1 (Upper left), 2 (Lower right)		UNLOCK			OK
MENU DIMMER	ON, OFF
CINEMA MODE *2	AUTO, VIDEO, FILM
REMOTE POSITION	AUTO, FRONT, REAR
LANGUAGE	, English, Español, Deutsch, Français, Italiano,			,	,	, Português
RESET ALL	OK

SIGNAL

HORIZ. POSITION *4

VERT. POSITION *4

FINE SYNC. *4

TRACKING *1 *4

COMPUTER INPUT

OVER SCAN

HOLD *4

USER

0 - 999	*3
0 - 999	*3
0 - 31
0 - 9999	*3

AUTO, RGB, YCBCR/YPBPR

100 - 90%	*3
ON	BEGIN
OFF	END
OK

0 - 99

0 - 99

CLAMP POSITION *4		1 - 255	*3
CLAMP WIDTH *4		1 - 63	*3
VERT. SYNC.		AUTO, OFF
LPF	*4 *5	ON, OFF
SHUTTER(U)		0 - 32
SHUTTER(L)		0 - 32
SHUTTER(LS)		0 - 95
SHUTTER(RS)		0 - 95

NETWORK

INFORMATION

PROJECTOR NAME NETWORK PASSWORD

IP CONFIG

PJLink CERTIFICATION

NETWORK RESET

LAMP TIME (LOW)

INPUT

RESOLUTION

VERTICAL FREQUENCY

HORIZONTAL FREQUENCY

SYNC. TYPE *4

xxxxx..., SET	DHCP	ON , OFF
OK	IP ADDRESS	xxx. xxx. xxx. xxx, SET
OK	SUBNET MASK	xxx. xxx. xxx. xxx, SET
ON , OFF	DEFAULT GATEWAY	xxx. xxx. xxx. xxx, SET
OK	MAC ADDRESS	xx-xx-xx-xx-xx-xx

*1: Not available with certain signals.

*2: Available only when the input signal is TV50, TV60, 480i, 576i or 1080i.

*3: Setting range differs depending on the input signals.

*4: Not available when the input signal is from the HDMI 1 or HDMI 2 terminal.

*5: Available only when the input signal is 480i, 480p, 576i, or 576p.

*6: Available only when the input signal is 480i, 480p, 576i, 576p, TV60 or TV50.

*7: Available only when RGB output is selected on the output device side.

EN-28