Mitsubishi Electronics HC7800DW user manual Viewing 3D images, Installing the 3D emitter

Page 25

Viewing 3D images

With the separately sold 3D glasses (EY-3DGS-78U), you can enjoy viewing 3D images on this projector. To view 3D images, install the supplied 3D emitter.

Installing the 3D emitter

1.Unplug the power cord of the projector.

2.Place the supplied non-slip sheet on the bottom of the 3D emitter.

Non-slip sheet

3D emitter

3.Connect the 3D emitter terminal on the 3D emitter to the 3D SYNC terminal on the projector using the supplied mini DIN 5-pin cable.

Important:

•Do not put any object which obstructs the communication between the 3D emitter and the 3D glasses.

•Do not place the 3D emitter near the remote control sensor of other devices.

•The transmission distance is decreased when the infra-red signal from the 3D emitter is transmitted to the 3D glasses by reflecting on the screen. In addition, the transmission distance in such case varies depending on the characteristics of the screen.

To 3D emitter	To 3D SYNC
terminal	terminal

Mini DIN 5-pin cable

4.Plug the power cord of the projector into the wall outlet and turn on the power.

•The indicator on the 3D emitter will light green and the 3D emitter will be ready to communicate with the 3D glasses.

5.Adjust the position and angle of the 3D emitter so that the 3D glasses can receive the infra-red signal.

•The traveling distance of the infra-red signal from the 3D emitter is about 10 m in straight line from the front of the infra-red transmission part.

•You can adjust the angle of the infra-red transmission part as shown below. Loosen the knob to adjust the angle and after finishing the adjustment, tighten the knob.

Infra-red transmission part

Knob

•Secure the 3D emitter using the supplied 3D emitter securing screws as necessary.

EN-25

Image 25

Contents HC7800D Risk of Electric Shock Do not Open Contents Important safeguards Important safeguards Removing the batteries from the remote control Inserting the batteries into the remote controlPreparing your projector What’s included in the boxOverview Preparing your projectorControl panel Picture quality adjusting buttons Remote controlPicture quality selection buttons Operational range of the remote control Using the remote controlReception angle Setting up the screen Setting up your projectorWhen the aspect ratio of the screen is Screen size and projection distanceWhen the aspect ratio of the screen is 2.351 CinemaScope Setting up your projectorWhen the aspect ratio of the image is When fine streaks are seen on projected images Adjusting the position of the projected imageWhen projected images are distorted to a trapezoid Correcting skewed or distorted imageTrigger terminal Front projection, ceiling mountingRear projection Viewing video images Connecting the projector to video equipmentBasic home theater system connection PreparationViewing video images Connecting to a DVD player or Hdtv decoderConnection for video equipment having an Hdmi terminal Connecting to video equipment having a Hdmi terminalPlugging in the power cord Projecting images To stop projecting ZOOM1 ZOOM2 Stretch ANAMORPHIC1 ANAMORPHIC2 Setting the aspect ratioWith the remote control How to change the settingsPlugging the power cord Connecting the projector to a computerViewing computer images About DDCComputer Viewing computer imagesSetting of the resolution When connecting to a notebook computerExample of the setting procedure for external output Auto Position buttonViewing 3D images Installing the 3D emitterViewing 3D images To change the 3D viewing mode3D images viewing To view 3D imagesEN-27 Menu operation You can make various settings using the displayed menusMenu operation How to set the menusPress the Menu button Menu selection bar is displayedImage menu Menu itemsSetup Auto Setting Function Advanced MenuScreen Size Vertical LocationInstallation menu Feature menu Signal menu Network menu Information menu Adjusting projected imagesAV memory To adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessAbout color temperature To adjust the tone of white Color TempTo enable the stored color temperature To optically brighten or darken projected images Auto IrisTo enable the stored gamma mode To adjust the ratio of change in brightness Gamma ModeTo use Color Management BLUEMAGENTAREDLPF Progressive filter To adjust the vertical positionPassword function Advanced featuresTo enable the password function To cancel the password functionMajor functions Advanced featuresConnection PJLink supported commandsSetting projector name Initial network settingsNetwork password settings IP settings Initial network settingsSetting or clearing Dhcp IP address settingsSubnet mask settings Initialization of network settingsDefault gateway settings Enabling or disabling the PJLink certificationGlossary How to use network functionDhcp Replacing the lamp Interval of lamp replacementReplacing the lamp When the projector is mounted to the ceilingReset of the lamp operation time Cleaning of the projector and the ventilation slots MaintenanceCleaning of the lens No image appears on the screen Problem TroubleshootingNo image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem Solution Others Problem Solution EN-55 EN-56 Power Status Condition IndicatorsCondition Possible Solution Normal conditionDimension drawings unit mm Specifications3D supported signals SpecificationsReplacement part option/not included in the box ConnectorsCOMPUTER/COMPONENT Video Hdmi 1, Hdmi VLT-HC7800LPZusho Baba, Nagaokakyo-City, Kyoto Japan