Microsoft G7VP2 manual Hardware Installation 3 PS/2 Mouse Port, Parallel Port

Page 26

2

Hardware Installation

2.9.3 PS/2 Mouse Port

The PS/2 mouse port is a 6-pin connector on the system board. Attach the 6-pin mouse port cable, which is mounted on a card- edge bracket, to connector J1. Make sure the red wire on the PS/2 mouse connector is aligned with pin 1 of connector J1. Mount the card-edge bracket to the system chassis.

Pin	Function
1	Mouse Data

2	Reserved

3	Ground

4	+5V

5	Mouse Clock

6	Reserved

2.9.4 Parallel Port

The system board has a stan- dard printer port for interfacing your PC to a parallel printer. It supports SPP, ECP and EPP modes. You can set the port’s mode in the Integrated Peripher- als setup of the Award BIOS.

Connecting the Parallel Printer

Port

Attach the DB-25 printer port cable to connector J9 on the

system board. Make sure the colored stripe on the ribbon cable aligns with pin 1 of J9. Use a small nutdriver to mount the cable into a DB-25 cutout in the system chassis. If your printer port cable is attached to a card-edge bracket, connect the cable to connector J9 on the system board and mount the card-edge bracket to the system chassis.

26

Image 26

Contents G7VP2 37310911Copyright TrademarksFCC and DOC Statement on Class B Table of Contents Supported Softwares Appendix B System Error MessageAppendix C Troubleshooting Appendix a Identifying ProcessorsIntroduction Features and SpecificationsFeatures IntroductionExpansion Slots ConnectorsLevel 2 Cache Memory Desktop Management Interface DMIIntelligence Watchdog Timer Dual Function Power Button ATX power supply onlyRTC Timer to Power-on the System ATX power supply only Virus ProtectionPackage Checklist System Board Layout Hardware InstallationHardware Installation Example on the right Switch Off DIP Switch Settings for Intel Processors DIP Switch Settings for Cyrix ProcessorsDIP Switch Settings for IBM Processors DIP Switch Settings for IDT ProcessorsDIP Switch Settings for AMD Processors External System Bus Clock Settings Frequency Ratio Settings for IDT Processors DIP Switch and Jumper Settings for Core Voltage Jumper Settings for Clearing Cmos Data Jumper JP1 Clear Cmos DataJumper Settings for Power Supply Type Jumper JP2 Power Supply TypeJumper JPP ATX Power-On/Off Select Pins 1 and 2 On ATX PowerJumper Settings for Sdram Clock Dimm Jumper JP4 Sdram ClockJumper Settings for Watchdog Timer Jumper JP10 Watchdog TimerConnecting the Serial Ports Serial PortsHardware Installation Keyboard Port/Connector Parallel Port Hardware Installation 3 PS/2 Mouse PortConnecting the Parallel Printer Port Hardware Installation Floppy Disk Drive Controller IDE Hard Disk InterfaceUniversal Serial Bus Ports Adding a Second IDE Hard DriveIrDA Connector Connecting the USB PortsHardware Installation CPU Fan Connector Chassis Fan ConnectorHardware Installation 11 J13 LEDs and Switches Keylock Keylock and Power LED Connector Hardware Installation Power Supply Connectors Standard Cmos Setup Award Bios Setup UtilityAward Bios Setup Utility Basic Input/Output SystemDate TimeHalt On Drive a and Drive BVideo Memory Award Bios Setup Utility Bios Features Setup Virus WarningBoot Up Floppy Seek Quick Power On Self TestBoot Sequence Boot Up NumLock StatusMemory ECC Function Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/SecHDD S.M.A.R.T. Capability Video Bios ShadowOS Select for Dram 64MB C8000-CBFFF Shadow to DC000-DFFFF ShadowAward Bios Setup Utility Chipset Features Setup Software Power-offCPU Fan Speed Limit and Chassis Fan Speed Limit CPU Temperature LimitSystem Health Monitor Power Management Setup +3.3V, +5V and +12V VoltagesVideo Off Method Power ManagementPM Control by APM Video Off AfterHDD Power Down Standby ModeSuspend Mode Soft-Off by PwrbtnDate of Month Resume On AlarmTimer hhmmss PM EventsResources Controlled By Award Bios Setup Utility 5 PNP/PCI ConfigurationReset Configuration Data PCI Slot 1 Use IRQ and PCI Slot 2 Use IRQ PCI IRQ Actived ByAssign IRQ for VGA Integrated Peripherals Award Bios Setup Utility Load Fail-Safe SettingsLoad Optimal Settings Onboard Primary PCI IDE and Onboard Secondary PCI IDE IDE Prefetch ModeIDE HDD Block Mode USB Keyboard Support Onboard Uart 2 ModeUSB Controller Onboard FDC ControllerOnboard Parallel Port IR Duplex ModeUse IR Pins Award Bios Setup Utility Supervisor Password User PasswordAward Bios Setup Utility IDE HDD Auto Detection Award Bios Setup Utility Save & Exit Setup Exit Without SavingSupported Softwares Supported SoftwaresDesktop Management Interface DMI Running the DMI UtilitySupported Softwares Using the DMI Utility Edit DMISave DMI File Supported Softwares Add DMILoad DMI File System Health Monitor Utility Genesys Logic System Health Monitor for VIAInstalling the Utility DriversCyrix Processors Appendix a Identifying ProcessorsIntel Processors Identifying ProcessorsIBM Processor AMD ProcessorsIDT Processors C6-PSME200GAPost Beep Appendix B System Error MessageError Messages System Error Message Troubleshooting C Appendix C -TroubleshootingTroubleshooting Checklist Monitor/DisplayFloppy Drive TroubleshootingPower Supply Troubleshooting Hard Drive Hard disk failureSystem Board Troubleshooting Serial PortKeyboard