Microsoft G7VP2 manual Standby Mode, Suspend Mode, HDD Power Down, Soft-Off by Pwrbtn

Page 46

3

Award BIOS Setup Utility

Standby Mode

This is user configurable only when the Power Management category is set to User Defined.When enabled and after the set time of system inactivity, the CPU clock will run at a slower speed (1/3 of full speed) while all other devices still operate at full speed.

Suspend Mode

This is user configurable only when the Power Management category is set to User Defined.When enabled and after the set time of system inactivity, the CPU and onboard peripherals will be shut off.

HDD Power Down

This is user configurable only when the Power Management category is set to User Defined.When enabled and after the set time of system inactivity, the hard disk drive will be powered down while all other devices remain active.

Soft-Off by PWRBTN

This category allows you to select the method of powering off your system.

Hold 4 Sec. Regardless of whether the Power Management field is enabled or disabled, if the power button is pushed and released in less than 4 sec, the system enters the Suspend mode. The purpose of this function is to prevent the system from powering off in case you accidentally “hit” or pushed the power button. Pushing the power button for more than 4 seconds will power off the system.

Instant-Off Pressing and then releasing the power button at once will immediately power off your system.

46

Image 46

Contents G7VP2 37310911Copyright TrademarksFCC and DOC Statement on Class B Table of Contents Supported Softwares Appendix B System Error MessageAppendix C Troubleshooting Appendix a Identifying ProcessorsIntroduction Features and SpecificationsFeatures IntroductionExpansion Slots ConnectorsLevel 2 Cache Memory Desktop Management Interface DMIIntelligence Watchdog Timer Dual Function Power Button ATX power supply onlyRTC Timer to Power-on the System ATX power supply only Virus ProtectionPackage Checklist Hardware Installation Hardware InstallationSystem Board Layout Example on the right Switch Off DIP Switch Settings for Intel Processors DIP Switch Settings for Cyrix ProcessorsDIP Switch Settings for IBM Processors DIP Switch Settings for IDT ProcessorsDIP Switch Settings for AMD Processors External System Bus Clock Settings Frequency Ratio Settings for IDT Processors DIP Switch and Jumper Settings for Core Voltage Jumper Settings for Clearing Cmos Data Jumper JP1 Clear Cmos DataJumper Settings for Power Supply Type Jumper JP2 Power Supply TypeJumper JPP ATX Power-On/Off Select Pins 1 and 2 On ATX PowerJumper Settings for Sdram Clock Dimm Jumper JP4 Sdram ClockJumper Settings for Watchdog Timer Jumper JP10 Watchdog TimerConnecting the Serial Ports Serial PortsHardware Installation Keyboard Port/Connector Connecting the Parallel Printer Port Hardware Installation 3 PS/2 Mouse PortParallel Port Hardware Installation Floppy Disk Drive Controller IDE Hard Disk InterfaceUniversal Serial Bus Ports Adding a Second IDE Hard DriveIrDA Connector Connecting the USB PortsHardware Installation CPU Fan Connector Chassis Fan ConnectorHardware Installation 11 J13 LEDs and Switches Keylock Keylock and Power LED Connector Hardware Installation Power Supply Connectors Standard Cmos Setup Award Bios Setup UtilityAward Bios Setup Utility Basic Input/Output SystemDate TimeVideo Drive a and Drive BHalt On Memory Award Bios Setup Utility Bios Features Setup Virus WarningBoot Up Floppy Seek Quick Power On Self TestBoot Sequence Boot Up NumLock StatusMemory ECC Function Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/SecHDD S.M.A.R.T. Capability Video Bios ShadowOS Select for Dram 64MB C8000-CBFFF Shadow to DC000-DFFFF ShadowAward Bios Setup Utility Chipset Features Setup Software Power-offSystem Health Monitor CPU Temperature LimitCPU Fan Speed Limit and Chassis Fan Speed Limit Power Management Setup +3.3V, +5V and +12V VoltagesVideo Off Method Power ManagementPM Control by APM Video Off AfterHDD Power Down Standby ModeSuspend Mode Soft-Off by PwrbtnDate of Month Resume On AlarmTimer hhmmss PM EventsReset Configuration Data Award Bios Setup Utility 5 PNP/PCI ConfigurationResources Controlled By Assign IRQ for VGA PCI IRQ Actived ByPCI Slot 1 Use IRQ and PCI Slot 2 Use IRQ Load Optimal Settings Award Bios Setup Utility Load Fail-Safe SettingsIntegrated Peripherals IDE HDD Block Mode IDE Prefetch ModeOnboard Primary PCI IDE and Onboard Secondary PCI IDE USB Keyboard Support Onboard Uart 2 ModeUSB Controller Onboard FDC ControllerUse IR Pins IR Duplex ModeOnboard Parallel Port Award Bios Setup Utility Supervisor Password User PasswordAward Bios Setup Utility IDE HDD Auto Detection Award Bios Setup Utility Save & Exit Setup Exit Without SavingSupported Softwares Supported SoftwaresDesktop Management Interface DMI Running the DMI UtilitySupported Softwares Using the DMI Utility Edit DMILoad DMI File Supported Softwares Add DMISave DMI File System Health Monitor Utility Genesys Logic System Health Monitor for VIAInstalling the Utility DriversCyrix Processors Appendix a Identifying ProcessorsIntel Processors Identifying ProcessorsIBM Processor AMD ProcessorsIDT Processors C6-PSME200GAError Messages Appendix B System Error MessagePost Beep System Error Message Troubleshooting C Appendix C -TroubleshootingTroubleshooting Checklist Monitor/DisplayPower Supply TroubleshootingFloppy Drive Troubleshooting Hard Drive Hard disk failureKeyboard Troubleshooting Serial PortSystem Board