Microsoft G7VP2 manual Table of Contents

Page 4

Table of Contents

Chapter 1 - Introduction

1.1

Features and Specifications

6

1.2

Package Checklist

10

Chapter 2 - Hardware Installation

 

2.1

System Board Layout

11

2.2

System Memory

12

2.3

DIP Switch and Jumper Settings of the Processors

12

2.4

Jumper Settings for Clearing CMOS Data

19

2.5

Jumper Settings for Power Supply Type

20

2.6

Jumper Settings for ATX Power-On/Off Select

21

2.7

Jumper Settings for SDRAM Clock (DIMM)

22

2.8

Jumper Settings for Watchdog Timer

23

2.9

Connecting the Ribbon Cables and Wires of the Ports

 

 

and Connectors

24

Chapter 3 - Award BIOS Setup Utility

 

3.1

The Basic Input/Output System

34

 

3.1.1

Standard CMOS Setup

34

 

3.1.2

BIOS Features Setup

38

 

3.1.3

Chipset Features Setup

42

 

3.1.4

Power Management Setup

44

 

3.1.5

PNP/PCI Configuration

48

 

3.1.6

Load Fail-Safe Settings

50

 

3.1.7

Load Optimal Settings

50

 

3.1.8

Integrated Peripherals

50

 

3.1.9

Supervisor Password

54

 

3.1.10

User Password

54

 

3.1.11

IDE HDD Auto Detection

55

 

3.1.12

Save & Exit Setup

56

 

3.1.13

Exit Without Saving

56

Image 4
Contents G7VP2 37310911Copyright TrademarksFCC and DOC Statement on Class B Table of Contents Appendix B System Error Message Appendix C TroubleshootingSupported Softwares Appendix a Identifying ProcessorsFeatures and Specifications FeaturesIntroduction IntroductionConnectors Level 2 Cache MemoryExpansion Slots Desktop Management Interface DMIIntelligence Dual Function Power Button ATX power supply only RTC Timer to Power-on the System ATX power supply onlyWatchdog Timer Virus ProtectionPackage Checklist Hardware Installation Hardware InstallationSystem Board Layout Example on the right Switch Off DIP Switch Settings for Intel Processors DIP Switch Settings for Cyrix ProcessorsDIP Switch Settings for IBM Processors DIP Switch Settings for IDT ProcessorsDIP Switch Settings for AMD Processors External System Bus Clock Settings Frequency Ratio Settings for IDT Processors DIP Switch and Jumper Settings for Core Voltage Jumper Settings for Clearing Cmos Data Jumper JP1 Clear Cmos DataJumper Settings for Power Supply Type Jumper JP2 Power Supply TypeJumper JPP ATX Power-On/Off Select Pins 1 and 2 On ATX PowerJumper Settings for Sdram Clock Dimm Jumper JP4 Sdram ClockJumper Settings for Watchdog Timer Jumper JP10 Watchdog TimerConnecting the Serial Ports Serial PortsHardware Installation Keyboard Port/Connector Connecting the Parallel Printer Port Hardware Installation 3 PS/2 Mouse PortParallel Port Hardware Installation Floppy Disk Drive Controller IDE Hard Disk InterfaceUniversal Serial Bus Ports Adding a Second IDE Hard DriveIrDA Connector Connecting the USB PortsHardware Installation CPU Fan Connector Chassis Fan ConnectorHardware Installation 11 J13 LEDs and Switches Keylock Keylock and Power LED Connector Hardware Installation Power Supply Connectors Award Bios Setup Utility Award Bios Setup UtilityStandard Cmos Setup Basic Input/Output SystemDate TimeVideo Drive a and Drive BHalt On Memory Award Bios Setup Utility Bios Features Setup Virus WarningQuick Power On Self Test Boot SequenceBoot Up Floppy Seek Boot Up NumLock StatusTypematic Rate Setting Typematic Delay MsecMemory ECC Function Typematic Rate Chars/SecVideo Bios Shadow OS Select for Dram 64MBHDD S.M.A.R.T. Capability C8000-CBFFF Shadow to DC000-DFFFF ShadowAward Bios Setup Utility Chipset Features Setup Software Power-offSystem Health Monitor CPU Temperature LimitCPU Fan Speed Limit and Chassis Fan Speed Limit Power Management Setup +3.3V, +5V and +12V VoltagesPower Management PM Control by APMVideo Off Method Video Off AfterStandby Mode Suspend ModeHDD Power Down Soft-Off by PwrbtnResume On Alarm Timer hhmmssDate of Month PM EventsReset Configuration Data Award Bios Setup Utility 5 PNP/PCI ConfigurationResources Controlled By Assign IRQ for VGA PCI IRQ Actived ByPCI Slot 1 Use IRQ and PCI Slot 2 Use IRQ Load Optimal Settings Award Bios Setup Utility Load Fail-Safe SettingsIntegrated Peripherals IDE HDD Block Mode IDE Prefetch ModeOnboard Primary PCI IDE and Onboard Secondary PCI IDE Onboard Uart 2 Mode USB ControllerUSB Keyboard Support Onboard FDC ControllerUse IR Pins IR Duplex ModeOnboard Parallel Port Award Bios Setup Utility Supervisor Password User PasswordAward Bios Setup Utility IDE HDD Auto Detection Award Bios Setup Utility Save & Exit Setup Exit Without SavingSupported Softwares Desktop Management Interface DMISupported Softwares Running the DMI UtilitySupported Softwares Using the DMI Utility Edit DMILoad DMI File Supported Softwares Add DMISave DMI File System Health Monitor Utility Genesys Logic System Health Monitor for VIAInstalling the Utility DriversAppendix a Identifying Processors Intel ProcessorsCyrix Processors Identifying ProcessorsIBM Processor AMD ProcessorsIDT Processors C6-PSME200GAError Messages Appendix B System Error MessagePost Beep System Error Message Appendix C -Troubleshooting Troubleshooting ChecklistTroubleshooting C Monitor/DisplayPower Supply TroubleshootingFloppy Drive Troubleshooting Hard Drive Hard disk failureKeyboard Troubleshooting Serial PortSystem Board