Microsoft G7VP2 manual Introduction, Features and Specifications

Page 6

1Introduction

Chapter 1 - Introduction

1.1 Features and Specifications

1.1.1 Features

Chipset

• VIA® Apollo 598MVP AGP system chipset

Processor

The system board is equipped with a switching voltage regulator that supports 2.0V to 3.5V core voltage for various processors.

•AMD® K5 PR90/PR100/PR120/PR133/PR166, K6-166/200/233/ 266/300, K6-2/250/266/300/333/350/366/380/400 or K6-III/ 400

•Intel Pentium® 90/100/120/133/150/166/200MHz or Intel Pentium® processor with MMXTM technology-166/200/233MHz

•Cyrix® 6x86L PR150+/PR166+/PR200+, 6x86MX-PR166/ PR200/PR233/PR266 or M II-300/333/350/400

•IBM® 6x86MX-PR200/PR233/PR266/PR300/PR333

•IDT® C6-180/200/225/240 or WinChip2-200/225/233/240/ 266/300

System Memory

The system board supports 8MB to 256MB of memory. It is equipped with two DIMM sockets. The 168-pin DIMM sockets use x64 EDO (60/70ns), SDRAM (10/12/13ns) or PC SDRAM (PC- 100 SDRAM for 100MHz external system bus clock processors), 3.3V.

DIMMs	Memory Size
1MBx64	8MB
2MBx64	16MB
4MBx64	32MB
8MBx64	64MB
16MBx64	128MB

6

Image 6

Contents G7VP2 37310911Copyright TrademarksFCC and DOC Statement on Class B Table of Contents Supported Softwares Appendix B System Error MessageAppendix C Troubleshooting Appendix a Identifying ProcessorsIntroduction Features and SpecificationsFeatures IntroductionExpansion Slots ConnectorsLevel 2 Cache Memory Desktop Management Interface DMIIntelligence Watchdog Timer Dual Function Power Button ATX power supply onlyRTC Timer to Power-on the System ATX power supply only Virus ProtectionPackage Checklist Hardware Installation Hardware InstallationSystem Board Layout Example on the right Switch Off DIP Switch Settings for Intel Processors DIP Switch Settings for Cyrix ProcessorsDIP Switch Settings for IBM Processors DIP Switch Settings for IDT ProcessorsDIP Switch Settings for AMD Processors External System Bus Clock Settings Frequency Ratio Settings for IDT Processors DIP Switch and Jumper Settings for Core Voltage Jumper Settings for Clearing Cmos Data Jumper JP1 Clear Cmos DataJumper Settings for Power Supply Type Jumper JP2 Power Supply TypeJumper JPP ATX Power-On/Off Select Pins 1 and 2 On ATX PowerJumper Settings for Sdram Clock Dimm Jumper JP4 Sdram ClockJumper Settings for Watchdog Timer Jumper JP10 Watchdog TimerConnecting the Serial Ports Serial PortsHardware Installation Keyboard Port/Connector Hardware Installation 3 PS/2 Mouse Port Connecting the Parallel Printer PortParallel Port Hardware Installation Floppy Disk Drive Controller IDE Hard Disk InterfaceUniversal Serial Bus Ports Adding a Second IDE Hard DriveIrDA Connector Connecting the USB PortsHardware Installation CPU Fan Connector Chassis Fan ConnectorHardware Installation 11 J13 LEDs and Switches Keylock Keylock and Power LED Connector Hardware Installation Power Supply Connectors Standard Cmos Setup Award Bios Setup UtilityAward Bios Setup Utility Basic Input/Output SystemDate TimeDrive a and Drive B VideoHalt On Memory Award Bios Setup Utility Bios Features Setup Virus WarningBoot Up Floppy Seek Quick Power On Self TestBoot Sequence Boot Up NumLock StatusMemory ECC Function Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/SecHDD S.M.A.R.T. Capability Video Bios ShadowOS Select for Dram 64MB C8000-CBFFF Shadow to DC000-DFFFF ShadowAward Bios Setup Utility Chipset Features Setup Software Power-offCPU Temperature Limit System Health MonitorCPU Fan Speed Limit and Chassis Fan Speed Limit Power Management Setup +3.3V, +5V and +12V VoltagesVideo Off Method Power ManagementPM Control by APM Video Off AfterHDD Power Down Standby ModeSuspend Mode Soft-Off by PwrbtnDate of Month Resume On AlarmTimer hhmmss PM EventsAward Bios Setup Utility 5 PNP/PCI Configuration Reset Configuration DataResources Controlled By PCI IRQ Actived By Assign IRQ for VGAPCI Slot 1 Use IRQ and PCI Slot 2 Use IRQ Award Bios Setup Utility Load Fail-Safe Settings Load Optimal SettingsIntegrated Peripherals IDE Prefetch Mode IDE HDD Block ModeOnboard Primary PCI IDE and Onboard Secondary PCI IDE USB Keyboard Support Onboard Uart 2 ModeUSB Controller Onboard FDC ControllerIR Duplex Mode Use IR PinsOnboard Parallel Port Award Bios Setup Utility Supervisor Password User PasswordAward Bios Setup Utility IDE HDD Auto Detection Award Bios Setup Utility Save & Exit Setup Exit Without SavingSupported Softwares Supported SoftwaresDesktop Management Interface DMI Running the DMI UtilitySupported Softwares Using the DMI Utility Edit DMISupported Softwares Add DMI Load DMI FileSave DMI File System Health Monitor Utility Genesys Logic System Health Monitor for VIAInstalling the Utility DriversCyrix Processors Appendix a Identifying ProcessorsIntel Processors Identifying ProcessorsIBM Processor AMD ProcessorsIDT Processors C6-PSME200GAAppendix B System Error Message Error MessagesPost Beep System Error Message Troubleshooting C Appendix C -TroubleshootingTroubleshooting Checklist Monitor/DisplayTroubleshooting Power SupplyFloppy Drive Troubleshooting Hard Drive Hard disk failureTroubleshooting Serial Port KeyboardSystem Board