Microsoft G7VP2 manual Resume On Alarm, Date of Month, Timer hhmmss, PM Events

Page 47

Award BIOS Setup Utility

Resume On Alarm

Enabled When Enabled,“Date (of Month)” and “Timer (hh:mm:ss)” will appear right below this field.You can set the date and time you would like the Soft Power Down (Soft-Off) PC to power-on.

Disabled Disables the automatic power-on function.(default)

Date (of Month)

0The system will power-on everyday according to the time set in the “Timer (hh:mm:ss)” field.

1-31 Select a date you would like the system to power-on.The system will power-on on the set date, and time set in the “Timer (hh:mm:ss)” field.

Timer (hh:mm:ss)

This is used to set the time you would like the system to power- on. If you want the system to power-on everyday as set in the “Date (of Month)” field, the time set in this field must be later than the CMOS RTC’s time.

PM Events

When enabled, access to the specified IRQ will cause the system to wake up completely from the power management mode. When disabled, the system will not wake up from the power management mode despite access to the specified IRQ.

3

47

Image 47
Contents 37310911 G7VP2Trademarks CopyrightFCC and DOC Statement on Class B Table of Contents Appendix a Identifying Processors Appendix B System Error MessageAppendix C Troubleshooting Supported SoftwaresIntroduction Features and SpecificationsFeatures IntroductionDesktop Management Interface DMI ConnectorsLevel 2 Cache Memory Expansion SlotsIntelligence Virus Protection Dual Function Power Button ATX power supply onlyRTC Timer to Power-on the System ATX power supply only Watchdog TimerPackage Checklist System Board Layout Hardware InstallationHardware Installation Example on the right Switch Off DIP Switch Settings for Cyrix Processors DIP Switch Settings for Intel ProcessorsDIP Switch Settings for IDT Processors DIP Switch Settings for IBM ProcessorsDIP Switch Settings for AMD Processors External System Bus Clock Settings Frequency Ratio Settings for IDT Processors DIP Switch and Jumper Settings for Core Voltage Jumper JP1 Clear Cmos Data Jumper Settings for Clearing Cmos DataJumper JP2 Power Supply Type Jumper Settings for Power Supply TypePins 1 and 2 On ATX Power Jumper JPP ATX Power-On/Off SelectJumper JP4 Sdram Clock Jumper Settings for Sdram Clock DimmJumper JP10 Watchdog Timer Jumper Settings for Watchdog TimerSerial Ports Connecting the Serial PortsHardware Installation Keyboard Port/Connector Parallel Port Hardware Installation 3 PS/2 Mouse PortConnecting the Parallel Printer Port IDE Hard Disk Interface Hardware Installation Floppy Disk Drive ControllerAdding a Second IDE Hard Drive Universal Serial Bus PortsConnecting the USB Ports IrDA ConnectorChassis Fan Connector Hardware Installation CPU Fan ConnectorHardware Installation 11 J13 LEDs and Switches Keylock Keylock and Power LED Connector Hardware Installation Power Supply Connectors Basic Input/Output System Award Bios Setup UtilityAward Bios Setup Utility Standard Cmos SetupTime DateHalt On Drive a and Drive BVideo Memory Virus Warning Award Bios Setup Utility Bios Features SetupBoot Up NumLock Status Quick Power On Self TestBoot Sequence Boot Up Floppy SeekTypematic Rate Chars/Sec Typematic Rate SettingTypematic Delay Msec Memory ECC FunctionC8000-CBFFF Shadow to DC000-DFFFF Shadow Video Bios ShadowOS Select for Dram 64MB HDD S.M.A.R.T. CapabilitySoftware Power-off Award Bios Setup Utility Chipset Features SetupCPU Fan Speed Limit and Chassis Fan Speed Limit CPU Temperature LimitSystem Health Monitor +3.3V, +5V and +12V Voltages Power Management SetupVideo Off After Power ManagementPM Control by APM Video Off MethodSoft-Off by Pwrbtn Standby ModeSuspend Mode HDD Power DownPM Events Resume On AlarmTimer hhmmss Date of MonthResources Controlled By Award Bios Setup Utility 5 PNP/PCI ConfigurationReset Configuration Data PCI Slot 1 Use IRQ and PCI Slot 2 Use IRQ PCI IRQ Actived ByAssign IRQ for VGA Integrated Peripherals Award Bios Setup Utility Load Fail-Safe SettingsLoad Optimal Settings Onboard Primary PCI IDE and Onboard Secondary PCI IDE IDE Prefetch ModeIDE HDD Block Mode Onboard FDC Controller Onboard Uart 2 ModeUSB Controller USB Keyboard SupportOnboard Parallel Port IR Duplex ModeUse IR Pins User Password Award Bios Setup Utility Supervisor PasswordAward Bios Setup Utility IDE HDD Auto Detection Exit Without Saving Award Bios Setup Utility Save & Exit SetupRunning the DMI Utility Supported SoftwaresDesktop Management Interface DMI Supported SoftwaresEdit DMI Supported Softwares Using the DMI UtilitySave DMI File Supported Softwares Add DMILoad DMI File Genesys Logic System Health Monitor for VIA System Health Monitor UtilityDrivers Installing the UtilityIdentifying Processors Appendix a Identifying ProcessorsIntel Processors Cyrix ProcessorsAMD Processors IBM ProcessorC6-PSME200GA IDT ProcessorsPost Beep Appendix B System Error MessageError Messages System Error Message Monitor/Display Appendix C -TroubleshootingTroubleshooting Checklist Troubleshooting CFloppy Drive TroubleshootingPower Supply Hard disk failure Troubleshooting Hard DriveSystem Board Troubleshooting Serial PortKeyboard