JVC DLA-X90R, DLA-X30, DLA-X70R manual Do not allow any unqualified person to install the unit

Page 4

1 Getting started

-The product should be placed more than one foot away from heat sources such as radiators, heat registers, stoves, and other products (including amplifiers) that produce heat.

-When connecting other products such as VCR’s, and DVD players, you should turn off the power of this product for protection against electric shock.

-Do not place combustibles behind the cooling fan.

For example, cloth, paper, matches, aerosol cans or gas lighters that present special hazards when over heated.

-Do not look into the projection lens while the illumination lamp is turned on. Exposure of your eyes to the strong light can result in impaired eyesight.

-Do not look into the inside of this unit through vents (ventilation holes), etc. Do not look at the illumination lamp directly by opening the cabinet while the illumination lamp is turned on. The illumination lamp also contains ultraviolet rays and the light is so powerful that your eyesight can be impaired.

-Do not drop, hit, or damage the light-source lamp

(lamp unit) in any way. It may cause the light- source lamp to break and lead to injuries. Do not use a damaged light source lamp. If the light- source lamp is broken, ask your dealer to repair it.

Fragments from a broken light-source lamp may cause injuries.

-The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the light-source lamp. If anything is unclear, please consult your dealer.

-Do not ceiling-mount the projector to a place which tends to vibrate; otherwise, the attaching fixture of the projector could be broken by the vibration, possibly causing it to fall or overturn, which could lead to personal injury.

-Use only the accessory cord designed for this product to prevent shock.

-For health reasons, please take a break of about 5-15 minutes every 30-60 minutes and let your eyes rest. Please refrain from watching any 3D- images when you feel tired, unwell or if you feel any other discomfort. Moreover, in case you see a double image, please adjust the equipment and software for proper display. Please stop using the unit if the double image is still visible after adjustment.

-Once every three years, please perform an internal test. This unit is provided with replacement parts needed to maintain its function (such as cooling fans). Estimated replacement time of parts can vary greatly depending on frequency of use and the respective environment. For replacement, please consult your dealer, or the nearest authorized JVC service center.

-When fixing the unit to the ceiling, Please note that we do not take any responsibility, even during the warranty period, if the product is damaged due to use of metal fixtures used for fixation to the ceiling other than our own or if the installation

4

environment of said metal fixtures is not appropriate. If the unit is suspended from the ceiling during use, please be careful in regard to the ambient temperature of the unit. If you use a central heating, the temperature close to the ceiling will be higher than normally expected.

-Video images can burn into the electronic com ponent parts. Please do not display screens with still images of high brightness or high contrast, such as found in video games and computer programs. Over a long period of time it might stick to the picture element. There is no problem with the playback of moving images, e.g. normal video footage.

-Not using the unit for a long time can lead to malfunction. Please power it on and let it run occasionally. Please avoid using the unit in a room where cigarettes are smoked. It is impos sible to clean optical component parts if they are contaminated by nicotine or tar. This might lead to performance degradation.

-Please watch from a distance three times the height of the projected image size. Persons with photosensitivity, any kind of heart disease, or weak health should not use 3D glasses.

-Watching 3D-images might be cause of illness. If you feel any change in your physical condition, please stop watching immediately and consult a physician if necessary.

-When watching 3D images, it is recommended to take regular breaks. As the length and frequency of the required breaks differ for every person, please judge according to your own condition.

-If your child watches while wearing 3D glasses, it should be accompanied by its parents or an adult guardian. The adult guardian should be careful to avoid situations where the child’s eyes might become tired, as responses to tiredness and discomfort, etc., are hard to detect, and it is possible for the physical condition to deteriorate very quickly. As the visual sense is not yet fully developed in children under the age of 6, please consult a physician in regard to any problem concerning 3D-images if necessary.

-Note that when using the 3D feature, the video output may appear different from the original video image due to image conversion on the device.

*DO NOT allow any unqualified person to install the unit.

Be sure to ask your dealer to install the unit (e.g.attaching it to the ceiling) since special technical knowledge and skills are required for installation. If installation is performed by an unqualified person, it may cause personal injury or electrical shock.

Image 4
Contents X70R/DLA-X30 JVC Kenwood CorporationInstrucción para el cliente PC021082599-1Safety Precautions About the installation placeGetting started Machine Noise Information Germany onlyPower source indicated on the label. If you are Not sure of the type of power supply to yourPower company This product is equipped with a three-wire plugDo not allow any unqualified person to install the unit Fragments from a broken light-source lamp may cause injuriesPower Connection United Kingdom only Power cordImportant Europe only Do not cut off the main plug from this equipmentBattery Products BatterieProdukte PileBaterías/pilas ProductosBatteria ProdottiBatteri ProdukterAkku TuotteetБатарея ИзделияBaterie ProduktyBaterija Produkt Samo u zemljama gde se primenjujeTHX Certification 90 THX CertificationFor detail information about ISF, please refer web site 90 Contents Accessories/Optional Accessories Check the AccessoriesOptional Accessories Please check with your authorized dealer for detailsMain body Front Controls and featuresMain body Bottom ⑪ Light receiving section Remote control rear ⑫ Power input terminalMain body Rear Left button Down buttonMain body About the indicator display Stand BYLight onGreenStand by BlinkingGreen DuringstandbyLighting/flashing lights Blinking Content Confirmation Main body Warning display and confirmation/responseAction Frequency CountermeasuresMain body Input terminal Remote Control To turn off the powerHow to insert batteries into the remote control To switch picture modeReference Display the information menuAbout installation Important points concerning the installationHow to adjust the vertical angle PreparationInstalling the Projector and Screen Lens shift correlation chartLeft/Right position Up/Down positionFixation of the projector Precautions for MountingBottom Surface Effective Range of Remote Control Unit When directing the remote control toward this unitWhen reflecting off a screen Screen Size and Projection DistanceTypes of possible input signals About the connectionTypes of possible input signals PC compatible Connection to the unit BD/DVD Recorder BD/DVD PlayerVCR CamcorderConnecting via Hdmi Cable Connecting via HDMI-DVI Conversion CableThis unit BD/DVD recorderConnecting via Component Video Cable Connecting via RGB Video CableConnecting via PC Cable 90 Connected by a 3D Synchro terminal3D synchro emitter This unitConnecting via Trigger Cable Connected by RS-232C connection cableSold separatelyTrigger input terminal Φ TerminalConnected by LAN terminal Connected by a Remote terminalNetwork ServerConnection of the power cord provided Be carful to avoid fire and electric shocksMemo Basic operation procedures Basic OperationAdjust the shift image position Turn off power sourceAbout Cool Down mode Adjust accordingly By pressing Up/down/left/right ButtonsFrequently used useful functions Project the imageAspect the image Input Image and Projected Image by Different Screen SizeTo end ExampleWhen there is a 3D input signal, adjustment is not possible Example When the Mask value is changed from Off 5%Mask the image Image for which quality at the outer area has deteriorated① Selec ② Confirm You can hide the image temporarilyUp and down Adjustments and settings in the menu Picture AdjustStructure of the menu hierarchy summary Color TempAdvanced SharpnessCustom Gamma Color ManagementWhen there is a PC signal Input, Aspect PC is Displayed Input SignalHdmi 3D Setting Pixel Adjust InstallationLens Control Function Display SetupNetwork When inputting Hdmi signals InformationMenu operation button MenuMenu operation procedure Menu item description Picture AdjustColor Profile This is the default value according to the picture mode To sub-menu1-2 Advanced Reset Color TempTo 1-1 Color Temp. of the submenu Gamma Dark/Bright LevelColor Temp Advanced Color SpaceCustom Gamma Color ManagementLamp Power Clear Motion DriveCMD Demo Lens ApertureCustom Gamma SharpnessDetail Enhance Color Management 90 Input Signal Items Explanation, operation, precautions, settingsPicture Position Aspect Video3D Setting Items Explanation, operation, precautions, settings InputHdmi MaskPhase PC 90Level Check Control with Hdmi3D Setting Installation Screen AdjustKeystone AnamorphicLens Control Pixel Adjust 90 Items Explanation, operation, precautions, settings AdjustAdjust Area Lens CoverPixel Adjust Adjust ColorAdjust Pattern Color AdjustPixelPixel Adjust Whole Adjust Pixel Red Vercital HorizontalSee Pixel Adjust Flow and Operation AdjustFine (-20/-20) ( 5 / 5 )Pixel Adjust Zone Adjust Red HorizontalVercital V10 H10 PositionDisplay Setup Function Network InformationGamma Curve Operation guide glossary100% Original Description of the 3D methodEye Left-eye image Right-eye image Stereoscopic video image Close Eye3D-glasses Left- eye imageLamp replacement procedure Replacing the LampInstall the new lamp unit UnitAttach the lamp cover After Replacing the LampSelectFunction Lamp Reset Resetting lamp TimeRe-confirm Red Lights Reset the lamp time by remote controlArrangement is used for Operations in this explanation Method for cleaning and replacing filters Clean the filterReinstall the inner filter If the filter is damaged or too dirty to be cleanedMemo Troubleshooting OthersIs the lamp near exhaustion? Off timer?Reference page 78 to Input terminal is connected but there is no signal Input the video signalsInput video signals that can be used No device is connected to the input terminalRS-232C Interface RS-232C SpecificationsTCP/IP-connection Command Format Command and dataBinary code Unit IDCommand Type Data description Remote control codeEnd Binary codeType Command Description Reference commandOperating command This section shows the communication examples of RS-232CILA Device Characteristics When Unit is Unused for a Long TimeParts Replacement Maintenance ProceduresAccessories Reference Operation Environment Temperature 5ºC to 35ºCSpecifications Others Unit mm DimensionsLens Index Remote control MessageLamp Lens
Related manuals
Manual 289 pages 25.29 Kb