JVC GV-LS2 U Establishing a wired connection, Attach the LAN cable to the unit in numerical order

Page 27

Establishing a wired connection

When establishing a wired connection to the computer or access point, attach the supplied LAN cable as follows.

Required operating environment

Browser: Internet Explorer 9 or later

1Set the network mode switch to "LAN(OFF)".

	R
	PLUG IN	MIC
RESET	PLUG IN
	POWE	DC
DIRECT WLAN	LAN(OFF)

AV

ETHERNET

DIRECT WLAN LAN(OFF)

•If the network mode switch is set to [DIRECT] or [WLAN], the LAN terminal cannot be used.

•While the power is on, switching the network mode switch does not change the setting.

2Attach the conversion cable to the stopper of the LAN cable.

Stopper

3Attach the LAN cable to the unit in numerical order.

21

MI	C P
MI	PLUG IN	AV
	OWER	AV	D
		EX	D
		TEN
			DC
			Hold the joint gently and insert.
		3

•Attach the cable without twisting.

•When using a tripod, make sure the cable does not come into contact with its handle.

•Do not put obstacles near the cable. Otherwise, the pantilter may not move properly.

•Do not use cables (AV cable, microphone, etc.) with L-shaped connecters.

•The center position of the camera may differ slightly under circumstances such as at low temperatures; however, this is not malfunction.

4Connect the camera to your computer via the LAN cable.

Preparation

27

Image 27

Contents GV-LS2 Table of Contents Connecting an External Mic Connecting the AV CordNetwork CAMERA/PAN Tilter Manage Verifying the Accessories Component Names and Functions CameraFront Back Bottom Introduction TopPantilter FrontBottom Back Use SettingAddition SetupExample 2 Record birds coming to a feeder on the balcony Example 3 Live-stream a performance in a studioStarting shooting Flow of Connection/SetupConnecting the Camera to Your Computer Required operating environmentAttach the LAN cable to the unit Connecting the AC Adapter List Configuring the initial settingsIP Address Subnet MaskHttp//condigured IP address8000 Configuring the Camera Settings Adjusting the clockSelect Common Settings in Manage Enter USERNAME, PASSWORD, and Password Confirm Setting the user name and passwordClick the Update button on the right Change Administrator USER/PASSWORDSelect an option from MAX Frame Rate MotionJPEG Select Stream Settings in NetworkMPEG-2 TS 720x576/MotionJPEG MPEG-2 TS 1920x1080/MotionJPEGSetting up the Ddns account Select Monitoring Settings in NetworkObtaining a Ddns account Click the ADD button Adding a camera drivers userSubnet Mask Establishing a wired connection to the access pointDefault Gateway Changing the Connection DestinationSelect Wireless Network in Network Connecting to the access point wirelessly Wi-FiUsing the WPS function Searching and connecting to the access pointEnter Password Click the Save button Connecting manuallyConnecting to a computer directly Wi-Fi Direct Click the Save button Select Common Settings in Manage Connecting Multiple CamerasScrew and fix the camera Attaching the PantilterAttaching the Pantilter Push the camera straight downLoosen the camera fixing screw sufficiently Connecting the AC adapterRemoving the pantilter Remove all tape from the pantilterConnect the camera to your computer via the LAN cable Establishing a wired connectionAttach the conversion cable to the stopper of the LAN cable Attach the LAN cable to the unit in numerical orderCompatible SD cards Inserting/Removing an SD CardInserting RemovingApproximate charging times Attaching/Removing the BatteryAttaching ChargingAttaching to the hot shoe Connecting an External MicConnecting to the camera Connecting to the pantilterConnecting the AV Cord Using the Unit Alone Turning on/off the powerStarting/Stopping recording Controlling from a Web Browser LoggingClick the LOG in button Status Controlling the camera Monitor tabMonitor File ManagementReload button Update images Setting button Zoom ratioSD card Configuring the camera settings Delete Managing files stored on the SD card File Management tabUse Folder/File lists TransferLOG in User Checking the message history Status tabCamera NetworkStreaming images Installing JVC CAM ControlUsing the Mobile Terminal Installing the App for mobile terminalsNames of Apps for mobile terminals Information Setting Item ListWired Network Wireless NetworkRegistered Access Point PasswordSSID, Authenticate METHOD, Password Ddns Monitoring SettingsPort Number UPnPStream Settings Stream 1 / StreamMAX Frame Rate MotionJPEG PAN Tilter Settings Camera SettingsMedia Management Common SettingsTurn OFF Camera Power cannot be turned on remotelyTroubleshooting Problem Check Refer toConnection Setup URLDirect Information Use Information Message Check Refer to Error messagesInstalled Update on this Incorrect PasswordNo Updates Available Update CorruptedPower WPS PowerLamp Status List To execute, click the Exec button Resetting to the factory settingsDeleting Resetting the connection information Click the Exec button on the rightTo avoid hazards Battery Pack optionalTo prevent damage and prolong service life Updating the firmwareVideo SpecificationsConnectors CameraMPEG-2 TS Stream output formatAC adapter UIA324-12 Pantilter GV-LS2WUPJVC Kenwood Corporation 0812HO-MW-VM