JVC GV-LS2 U manual Incorrect Password, USE AC Adapter, No Updates Available, Update Corrupted

Page 54

Information

Message

Check

Refer to

 

 

 

 

• The two passwords entered on the change password

 

INCORRECT PASSWORD

screen are different. Enter the same password in the

–

 

two fields.

 

 

 

 

USE AC ADAPTER

• When updating the firmware, connect the AC adapter.

page 12

 

 

 

NO UPDATES AVAILABLE

• Check if the update file is written in the correct folder

–

on the SD card.

 

 

 

 

 

UPDATE CORRUPTED

• Retrieve the firmware update file, and copy it to the SD

–

card.

 

 

 

 

 

INSTALLED UPDATE ON THIS

• Obtain the updater for the unit.

–

CAMERA CAN NOT BE USED

 

 

 

 

 

UPDATE IS SAME OR OLDER

• The firmware has already been updated. There is no

 

VERSION. NO INSTALLATION

–

need to update it.

REQUIRED

 

 

 

 

 

 

POWER TURNED OFF TO

• The power is automatically turned off if "AUTO POWER

 

OFF" is set to "ON", the unit runs with the battery, and

page 46

CONSERVE BATTERY POWER

no operation is performed for 5 minutes.

 

 

 

 

 

 

(12 HOURS LIMITATION)

• Recording stops automatically as it cannot be

–

RECORDING CANCELLED

performed for 12 or more consecutive hours.

 

 

 

 

ABNORMALITY OCCURRED IN

• Turn on the power again, and retry.

page 7

PAN TILTER

 

 

 

 

 

POWER TURNED OFF AS

 

 

CAMERA TEMPERATURE IS TOO

• Wait for a while, and turn on the power again.

page 6

HOT

 

 

 

 

 

PROCESS FAILED

• Setup, file deletion, etc. failed for some reason. Check

–

the connection, and retry.

 

 

 

 

 

54

Page 53 Page 55
Image 54
Page 53 Page 55
Contents GV-LS2 Table of Contents Connecting an External Mic Connecting the AV CordNetwork CAMERA/PAN Tilter Manage Verifying the Accessories Component Names and Functions CameraFront Back Introduction Top BottomPantilter FrontBottom Back Setting UseExample 3 Live-stream a performance in a studio SetupExample 2 Record birds coming to a feeder on the balcony AdditionFlow of Connection/Setup Starting shootingConnecting the Camera to Your Computer Required operating environmentAttach the LAN cable to the unit Connecting the AC Adapter Subnet Mask Configuring the initial settingsIP Address ListHttp//condigured IP address8000 Configuring the Camera Settings Adjusting the clockSelect Common Settings in Manage Change Administrator USER/PASSWORD Setting the user name and passwordClick the Update button on the right Enter USERNAME, PASSWORD, and Password ConfirmMPEG-2 TS 1920x1080/MotionJPEG Select Stream Settings in NetworkMPEG-2 TS 720x576/MotionJPEG Select an option from MAX Frame Rate MotionJPEGSetting up the Ddns account Select Monitoring Settings in NetworkObtaining a Ddns account Adding a camera drivers user Click the ADD buttonChanging the Connection Destination Establishing a wired connection to the access pointDefault Gateway Subnet MaskSearching and connecting to the access point Connecting to the access point wirelessly Wi-FiUsing the WPS function Select Wireless Network in NetworkConnecting manually Enter Password Click the Save buttonConnecting to a computer directly Wi-Fi Direct Connecting Multiple Cameras Click the Save button Select Common Settings in ManagePush the camera straight down Attaching the PantilterAttaching the Pantilter Screw and fix the cameraRemove all tape from the pantilter Connecting the AC adapterRemoving the pantilter Loosen the camera fixing screw sufficientlyAttach the LAN cable to the unit in numerical order Establishing a wired connectionAttach the conversion cable to the stopper of the LAN cable Connect the camera to your computer via the LAN cableRemoving Inserting/Removing an SD CardInserting Compatible SD cardsCharging Attaching/Removing the BatteryAttaching Approximate charging timesConnecting to the pantilter Connecting an External MicConnecting to the camera Attaching to the hot shoeConnecting the AV Cord Using the Unit Alone Turning on/off the powerStarting/Stopping recording Controlling from a Web Browser LoggingClick the LOG in button File Management Controlling the camera Monitor tabMonitor StatusReload button Update images Setting button Zoom ratioSD card Configuring the camera settings Transfer Managing files stored on the SD card File Management tabUse Folder/File lists DeleteNetwork Checking the message history Status tabCamera LOG in UserInstalling JVC CAM Control Streaming imagesUsing the Mobile Terminal Installing the App for mobile terminalsNames of Apps for mobile terminals Wireless Network Setting Item ListWired Network InformationRegistered Access Point PasswordSSID, Authenticate METHOD, Password UPnP Monitoring SettingsPort Number DdnsStream Settings Stream 1 / StreamMAX Frame Rate MotionJPEG Camera Settings PAN Tilter SettingsCommon Settings Media ManagementPower cannot be turned on remotely Turn OFF CameraTroubleshooting Problem Check Refer toConnection Setup URLDirect Information Use Information Error messages Message Check Refer toUpdate Corrupted Incorrect PasswordNo Updates Available Installed Update on thisPower WPS PowerLamp Status List Click the Exec button on the right Resetting to the factory settingsDeleting Resetting the connection information To execute, click the Exec buttonUpdating the firmware Battery Pack optionalTo prevent damage and prolong service life To avoid hazardsCamera SpecificationsConnectors VideoPantilter GV-LS2WUP Stream output formatAC adapter UIA324-12 MPEG-2 TSJVC Kenwood Corporation 0812HO-MW-VM
Top Page Image Contents