JVC GV-LS2 U manual Attaching/Removing the Battery, Charging, Approximate charging times

Page 29

Attaching/Removing the Battery

The camera can run with the battery power only. When the battery (BN-VG139U) (sold separately) is attached, videos can be transmitted/recorded even in places where the AC adapter cannot be used.

•The battery cannot be used when the pantilter is attached.

•Turn off the power before attaching/removing the battery.

•The following cannot be used while the battery is attached:

– LAN terminal, network mode switch, reset button

CAUTION

•Be sure to use a battery of our manufacture. If a battery not of our manufacture is used, the safety and performance are not guaranteed.

•Charging may take time or may not be possible in places outside the operating temperature range.

Attaching

Insert the battery deeply, and then slide it to the right until it clicks.

Removing

Slide the battery to the left, and pull it out toward you while pushing in the lever below the battery.

Charging

Connect the adapter to the DC connector of the camera, and turn off the power. Charging starts.

The power button of the camera blinks during charging. The power button turns off when charging is complete.

Approximate charging times

		Charging time

	BN-VG139U (sold	6 hr. 10 min.
	separately)	6 hr. 10 min.
	separately)

	Approximate recording times

		Actual	Continuous
		shooting time	shooting time

	BN-VG139U (sold	1 hr. 55 min.	2 hr. 55 min.
	separately)	1 hr. 55 min.	2 hr. 55 min.
	separately)

Preparation

29

Image 29

Contents GV-LS2 Table of Contents Network CAMERA/PAN Tilter Manage Connecting an External MicConnecting the AV Cord Verifying the Accessories Front Back Component Names and FunctionsCamera Bottom Introduction TopBottom Back PantilterFront Use SettingExample 2 Record birds coming to a feeder on the balcony SetupExample 3 Live-stream a performance in a studio AdditionStarting shooting Flow of Connection/SetupAttach the LAN cable to the unit Connecting the Camera to Your ComputerRequired operating environment Connecting the AC Adapter IP Address Configuring the initial settingsSubnet Mask ListHttp//condigured IP address8000 Select Common Settings in Manage Configuring the Camera SettingsAdjusting the clock Click the Update button on the right Setting the user name and passwordChange Administrator USER/PASSWORD Enter USERNAME, PASSWORD, and Password ConfirmMPEG-2 TS 720x576/MotionJPEG Select Stream Settings in NetworkMPEG-2 TS 1920x1080/MotionJPEG Select an option from MAX Frame Rate MotionJPEGObtaining a Ddns account Setting up the Ddns accountSelect Monitoring Settings in Network Click the ADD button Adding a camera drivers userDefault Gateway Establishing a wired connection to the access pointChanging the Connection Destination Subnet MaskUsing the WPS function Connecting to the access point wirelessly Wi-FiSearching and connecting to the access point Select Wireless Network in NetworkEnter Password Click the Save button Connecting manuallyConnecting to a computer directly Wi-Fi Direct Click the Save button Select Common Settings in Manage Connecting Multiple CamerasAttaching the Pantilter Attaching the PantilterPush the camera straight down Screw and fix the cameraRemoving the pantilter Connecting the AC adapterRemove all tape from the pantilter Loosen the camera fixing screw sufficientlyAttach the conversion cable to the stopper of the LAN cable Establishing a wired connectionAttach the LAN cable to the unit in numerical order Connect the camera to your computer via the LAN cableInserting Inserting/Removing an SD CardRemoving Compatible SD cardsAttaching Attaching/Removing the BatteryCharging Approximate charging timesConnecting to the camera Connecting an External MicConnecting to the pantilter Attaching to the hot shoeConnecting the AV Cord Starting/Stopping recording Using the Unit AloneTurning on/off the power Click the LOG in button Controlling from a Web BrowserLogging Monitor Controlling the camera Monitor tabFile Management StatusSD card Reload button Update images Setting buttonZoom ratio Configuring the camera settings Use Folder/File lists Managing files stored on the SD card File Management tabTransfer DeleteCamera Checking the message history Status tabNetwork LOG in UserStreaming images Installing JVC CAM ControlNames of Apps for mobile terminals Using the Mobile TerminalInstalling the App for mobile terminals Wired Network Setting Item ListWireless Network InformationSSID, Authenticate METHOD, Password Registered Access PointPassword Port Number Monitoring SettingsUPnP DdnsMAX Frame Rate MotionJPEG Stream SettingsStream 1 / Stream PAN Tilter Settings Camera SettingsMedia Management Common SettingsTurn OFF Camera Power cannot be turned on remotelyConnection TroubleshootingProblem Check Refer to Direct SetupURL Information Use Information Message Check Refer to Error messagesNo Updates Available Incorrect PasswordUpdate Corrupted Installed Update on thisLamp Status List PowerWPS Power Deleting Resetting the connection information Resetting to the factory settingsClick the Exec button on the right To execute, click the Exec buttonTo prevent damage and prolong service life Battery Pack optionalUpdating the firmware To avoid hazardsConnectors SpecificationsCamera VideoAC adapter UIA324-12 Stream output formatPantilter GV-LS2WUP MPEG-2 TSJVC Kenwood Corporation 0812HO-MW-VM