JVC GV-LS2 U manual Component Names and Functions, Camera, Front Back

Page 5

Component Names and Functions

Camera

Front

Back

Introduction

1

3

4 5

2

1 Internal mic (stereo)

1

2

1Reset button

	5
	R
	PLUG IN	MIC
RESET	PLUG IN
	POWE	DC
DIRECT WLAN	LAN(OFF)

AV ETHERNET

34

6

7

8

Transmits/Records sounds coming through this mic

when no external mic is connected.

2Lens

Be careful not to touch directly or let anything come into contact.

3LED light

Works as a light in dark places. Turn on/off from a browser. ( ➭ page 36)

4Information lamp

Can be lit up to indicate the recording status, etc.

5Camera sensor

Adjusts the white balance automatically. Make sure that this sensor is not hidden behind any objects.

Resets the network settings when you press and hold this button with the tip of a paper clip or the like for 3 seconds or longer while the AC adapter is connected. ( ➭ page 56)

Use it e.g. if a wrong network setting has been configured and a connection cannot be established.

2LAN terminal

Connect a LAN cable to establish a wired connection to the computer or access point (router). ( ➭ page 11)

3Network mode switch

Switches the network mode. ( ➭ page 20)

DIRECT: To connect to a computer wirelessly (Wi-Fi)

WLAN: To connect to an access point (wireless LAN router) wirelessly (Wi-Fi)

LAN(OFF): To establish a wired connection, or to establish no wireless connection

4Battery terminal

Connect a separately purchased battery pack (BN-

VG139U) e.g. when using outdoors. ( ➭ page 29)

5SD card slot

Insert an SD card here to save recorded data to the card.

For compatible cards, see page 28.

6Mic terminal

Connect an external mic to transmit/record external

sounds. ( ➭ page 30)

7DC connector

Connect the supplied AC adapter when using with AC power. ( ➭ page 12)

8AV connector

Connect a separately purchased AV cord to watch videos being transmitted/recorded. ( ➭ page 31)

5

Image 5

Contents GV-LS2 Table of Contents Network CAMERA/PAN Tilter Manage Connecting an External MicConnecting the AV Cord Verifying the Accessories Front Back Component Names and FunctionsCamera Bottom Introduction TopBottom Back PantilterFront Use SettingExample 2 Record birds coming to a feeder on the balcony SetupExample 3 Live-stream a performance in a studio AdditionStarting shooting Flow of Connection/SetupAttach the LAN cable to the unit Connecting the Camera to Your ComputerRequired operating environment Connecting the AC Adapter IP Address Configuring the initial settingsSubnet Mask ListHttp//condigured IP address8000 Select Common Settings in Manage Configuring the Camera SettingsAdjusting the clock Click the Update button on the right Setting the user name and passwordChange Administrator USER/PASSWORD Enter USERNAME, PASSWORD, and Password ConfirmMPEG-2 TS 720x576/MotionJPEG Select Stream Settings in NetworkMPEG-2 TS 1920x1080/MotionJPEG Select an option from MAX Frame Rate MotionJPEGObtaining a Ddns account Setting up the Ddns accountSelect Monitoring Settings in Network Click the ADD button Adding a camera drivers userDefault Gateway Establishing a wired connection to the access pointChanging the Connection Destination Subnet MaskUsing the WPS function Connecting to the access point wirelessly Wi-FiSearching and connecting to the access point Select Wireless Network in NetworkEnter Password Click the Save button Connecting manuallyConnecting to a computer directly Wi-Fi Direct Click the Save button Select Common Settings in Manage Connecting Multiple CamerasAttaching the Pantilter Attaching the PantilterPush the camera straight down Screw and fix the cameraRemoving the pantilter Connecting the AC adapterRemove all tape from the pantilter Loosen the camera fixing screw sufficientlyAttach the conversion cable to the stopper of the LAN cable Establishing a wired connectionAttach the LAN cable to the unit in numerical order Connect the camera to your computer via the LAN cableInserting Inserting/Removing an SD CardRemoving Compatible SD cardsAttaching Attaching/Removing the BatteryCharging Approximate charging timesConnecting to the camera Connecting an External MicConnecting to the pantilter Attaching to the hot shoeConnecting the AV Cord Starting/Stopping recording Using the Unit AloneTurning on/off the power Click the LOG in button Controlling from a Web BrowserLogging Monitor Controlling the camera Monitor tabFile Management StatusSD card Reload button Update images Setting buttonZoom ratio Configuring the camera settings Use Folder/File lists Managing files stored on the SD card File Management tabTransfer DeleteCamera Checking the message history Status tabNetwork LOG in UserStreaming images Installing JVC CAM ControlNames of Apps for mobile terminals Using the Mobile TerminalInstalling the App for mobile terminals Wired Network Setting Item ListWireless Network InformationSSID, Authenticate METHOD, Password Registered Access PointPassword Port Number Monitoring SettingsUPnP DdnsMAX Frame Rate MotionJPEG Stream SettingsStream 1 / Stream PAN Tilter Settings Camera SettingsMedia Management Common SettingsTurn OFF Camera Power cannot be turned on remotelyConnection TroubleshootingProblem Check Refer to Direct SetupURL Information Use Information Message Check Refer to Error messagesNo Updates Available Incorrect PasswordUpdate Corrupted Installed Update on thisLamp Status List PowerWPS Power Deleting Resetting the connection information Resetting to the factory settingsClick the Exec button on the right To execute, click the Exec buttonTo prevent damage and prolong service life Battery Pack optionalUpdating the firmware To avoid hazardsConnectors SpecificationsCamera VideoAC adapter UIA324-12 Stream output formatPantilter GV-LS2WUP MPEG-2 TSJVC Kenwood Corporation 0812HO-MW-VM