JVC GV-LS2 U manual Connecting to the access point wirelessly Wi-Fi, Using the WPS function

Page 21

Connecting to the access point wirelessly (Wi-Fi)

Using the WPS function

Connect to the access point equipped with the WPS function easily.

1Press and hold the power button to power off.

2Disconnect the LAN cable that connects the camera to your computer.

3Set the network mode switch to "WLAN".

4Press and hold the power button to power on. The record button starts blinking. Wait until it stops blinking and off.

5Enable the WPS function of the access point. (Example) Press the "WPS" button.

For how to enable the WPS function, refer to the instruction manual of the access point.

6Press and hold the "WPS" button.

When the "WPS" button stops blinking and stays lit, the connection is complete.

If no connection can be established within two minutes, the "WPS" button turns off. Try again, or set up manually.

Searching and connecting to the access point

1Select "WIRELESS NETWORK" in "NETWORK".

If the sub settings are not displayed, click "+" on the left of "NETWORK".

2Click the "SEARCH" button.

3Select an access point to connect to.

If your preferred access point is not in the list, click the "SEARCH AGAIN" button.

It may not be found if there is a long distance or interference.

Preparation

21

Image 21

Contents GV-LS2 Table of Contents Connecting an External Mic Connecting the AV CordNetwork CAMERA/PAN Tilter Manage Verifying the Accessories Component Names and Functions CameraFront Back Bottom Introduction TopPantilter FrontBottom Back Use SettingExample 2 Record birds coming to a feeder on the balcony SetupExample 3 Live-stream a performance in a studio AdditionStarting shooting Flow of Connection/SetupConnecting the Camera to Your Computer Required operating environmentAttach the LAN cable to the unit Connecting the AC Adapter IP Address Configuring the initial settingsSubnet Mask ListHttp//condigured IP address8000 Configuring the Camera Settings Adjusting the clockSelect Common Settings in Manage Click the Update button on the right Setting the user name and passwordChange Administrator USER/PASSWORD Enter USERNAME, PASSWORD, and Password ConfirmMPEG-2 TS 720x576/MotionJPEG Select Stream Settings in NetworkMPEG-2 TS 1920x1080/MotionJPEG Select an option from MAX Frame Rate MotionJPEGSetting up the Ddns account Select Monitoring Settings in NetworkObtaining a Ddns account Click the ADD button Adding a camera drivers userDefault Gateway Establishing a wired connection to the access pointChanging the Connection Destination Subnet MaskUsing the WPS function Connecting to the access point wirelessly Wi-FiSearching and connecting to the access point Select Wireless Network in NetworkEnter Password Click the Save button Connecting manuallyConnecting to a computer directly Wi-Fi Direct Click the Save button Select Common Settings in Manage Connecting Multiple CamerasAttaching the Pantilter Attaching the PantilterPush the camera straight down Screw and fix the cameraRemoving the pantilter Connecting the AC adapterRemove all tape from the pantilter Loosen the camera fixing screw sufficientlyAttach the conversion cable to the stopper of the LAN cable Establishing a wired connectionAttach the LAN cable to the unit in numerical order Connect the camera to your computer via the LAN cableInserting Inserting/Removing an SD CardRemoving Compatible SD cardsAttaching Attaching/Removing the BatteryCharging Approximate charging timesConnecting to the camera Connecting an External MicConnecting to the pantilter Attaching to the hot shoeConnecting the AV Cord Using the Unit Alone Turning on/off the powerStarting/Stopping recording Controlling from a Web Browser LoggingClick the LOG in button Monitor Controlling the camera Monitor tabFile Management StatusReload button Update images Setting button Zoom ratioSD card Configuring the camera settings Use Folder/File lists Managing files stored on the SD card File Management tabTransfer DeleteCamera Checking the message history Status tabNetwork LOG in UserStreaming images Installing JVC CAM ControlUsing the Mobile Terminal Installing the App for mobile terminalsNames of Apps for mobile terminals Wired Network Setting Item ListWireless Network InformationRegistered Access Point PasswordSSID, Authenticate METHOD, Password Port Number Monitoring SettingsUPnP DdnsStream Settings Stream 1 / StreamMAX Frame Rate MotionJPEG PAN Tilter Settings Camera SettingsMedia Management Common SettingsTurn OFF Camera Power cannot be turned on remotelyTroubleshooting Problem Check Refer toConnection Setup URLDirect Information Use Information Message Check Refer to Error messagesNo Updates Available Incorrect PasswordUpdate Corrupted Installed Update on thisPower WPS PowerLamp Status List Deleting Resetting the connection information Resetting to the factory settingsClick the Exec button on the right To execute, click the Exec buttonTo prevent damage and prolong service life Battery Pack optionalUpdating the firmware To avoid hazardsConnectors SpecificationsCamera VideoAC adapter UIA324-12 Stream output formatPantilter GV-LS2WUP MPEG-2 TSJVC Kenwood Corporation 0812HO-MW-VM