JVC GV-LS2 U manual Camera Settings, PAN Tilter Settings

Page 45

"CAMERA/PAN TILTER"

Configure the settings for the camera and pantilter on "CAMERA/PAN TILTER". Categorized into "CAMERA SETTINGS" and "PAN TILTER SETTINGS".

"CAMERA SETTINGS"

Change the camera settings.

1

2

3

4

5 6

7

1AUTO ZOOM RESET

Select "OFF" or "ON" for the function that resets the zoom ratio automatically if no operation is performed for 5 minutes.

2WIND CUT

Select "OFF" or "ON" for the function that reduces noise such as wind sounds.

3MIC LEVEL SETTING

Select "+2", "+1", "0", "-1", or "-2" for the audio input level of an external mic.

When the sounds are too loud, set it to a smaller value. When the sounds are too low, set it to a larger value.

4MAX ZOOM RATIO

Select the zoom method and maximum ratio. The options vary depending on the model.

Select "10X/OPTICAL", "16X/DYNAMIC", "64X/ DIGITAL", or "200X/DIGITAL".

5ZOOM AMOUNT (ZOOM1)

Select "x1", "x2", or "x3" for the amount zoomed when the inside button is pressed.

6ZOOM AMOUNT (ZOOM2)

Select "x1", "x2", or "x3" for the amount zoomed when the outside button is pressed.

7"SAVE" button

After changing the above settings, click this button to save the changes.

"PAN TILTER SETTINGS"

Change the pantilter settings.

1

2

3

1AUTO RESET POSITION

Select "OFF" or "ON" for the function that resets the camera position automatically if no operation is performed for 5 minutes.

2Pantilter rotation angle

ROTATE ANGLE (PAN1)

Set the value within the range of 1 to 90 degrees for the angle rotated when the inside pan button is pressed.

ROTATE ANGLE (PAN2)

Set the value within the range of 1 to 90 degrees for the angle rotated when the outside pan button is pressed.

ROTATE ANGLE (TILT1)

Set the value within the range of 1 to 70 degrees for the angle rotated when the inside tilt button is pressed.

ROTATE ANGLE (TILT2)

Set the value within the range of 1 to 70 degrees for the angle rotated when the outside tilt button is pressed.

3"SAVE" button

After changing the above settings, click this button to save the changes.

Information

45

Image 45

Contents GV-LS2 Table of Contents Connecting an External Mic Connecting the AV CordNetwork CAMERA/PAN Tilter Manage Verifying the Accessories Component Names and Functions CameraFront Back Bottom Introduction TopPantilter FrontBottom Back Use SettingExample 2 Record birds coming to a feeder on the balcony SetupExample 3 Live-stream a performance in a studio AdditionStarting shooting Flow of Connection/SetupConnecting the Camera to Your Computer Required operating environmentAttach the LAN cable to the unit Connecting the AC Adapter IP Address Configuring the initial settingsSubnet Mask ListHttp//condigured IP address8000 Configuring the Camera Settings Adjusting the clockSelect Common Settings in Manage Click the Update button on the right Setting the user name and passwordChange Administrator USER/PASSWORD Enter USERNAME, PASSWORD, and Password ConfirmMPEG-2 TS 720x576/MotionJPEG Select Stream Settings in NetworkMPEG-2 TS 1920x1080/MotionJPEG Select an option from MAX Frame Rate MotionJPEGSetting up the Ddns account Select Monitoring Settings in NetworkObtaining a Ddns account Click the ADD button Adding a camera drivers userDefault Gateway Establishing a wired connection to the access pointChanging the Connection Destination Subnet MaskUsing the WPS function Connecting to the access point wirelessly Wi-FiSearching and connecting to the access point Select Wireless Network in NetworkEnter Password Click the Save button Connecting manuallyConnecting to a computer directly Wi-Fi Direct Click the Save button Select Common Settings in Manage Connecting Multiple CamerasAttaching the Pantilter Attaching the PantilterPush the camera straight down Screw and fix the cameraRemoving the pantilter Connecting the AC adapterRemove all tape from the pantilter Loosen the camera fixing screw sufficientlyAttach the conversion cable to the stopper of the LAN cable Establishing a wired connectionAttach the LAN cable to the unit in numerical order Connect the camera to your computer via the LAN cableInserting Inserting/Removing an SD CardRemoving Compatible SD cardsAttaching Attaching/Removing the BatteryCharging Approximate charging timesConnecting to the camera Connecting an External MicConnecting to the pantilter Attaching to the hot shoeConnecting the AV Cord Using the Unit Alone Turning on/off the powerStarting/Stopping recording Controlling from a Web Browser LoggingClick the LOG in button Monitor Controlling the camera Monitor tabFile Management StatusReload button Update images Setting button Zoom ratioSD card Configuring the camera settings Use Folder/File lists Managing files stored on the SD card File Management tabTransfer DeleteCamera Checking the message history Status tabNetwork LOG in UserStreaming images Installing JVC CAM ControlUsing the Mobile Terminal Installing the App for mobile terminalsNames of Apps for mobile terminals Wired Network Setting Item ListWireless Network InformationRegistered Access Point PasswordSSID, Authenticate METHOD, Password Port Number Monitoring SettingsUPnP DdnsStream Settings Stream 1 / StreamMAX Frame Rate MotionJPEG PAN Tilter Settings Camera SettingsMedia Management Common SettingsTurn OFF Camera Power cannot be turned on remotelyTroubleshooting Problem Check Refer toConnection Setup URLDirect Information Use Information Message Check Refer to Error messagesNo Updates Available Incorrect PasswordUpdate Corrupted Installed Update on thisPower WPS PowerLamp Status List Deleting Resetting the connection information Resetting to the factory settingsClick the Exec button on the right To execute, click the Exec buttonTo prevent damage and prolong service life Battery Pack optionalUpdating the firmware To avoid hazardsConnectors SpecificationsCamera VideoAC adapter UIA324-12 Stream output formatPantilter GV-LS2WUP MPEG-2 TSJVC Kenwood Corporation 0812HO-MW-VM