Sharp XG-P610X-N quick start Controlling the Projector by a Computer

Page 29

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to the RS-232C serial terminal on the computer, or when the LAN terminal on the projector is connected to the LAN terminal on the computer, the computer can be used to control the projector. Refer to the ÒSETUP MANUALÓ contained on the supplied CD-ROM for details.

When connecting to a computer using an RS-232C serial control cable

Computer

To RS-232C terminal

Rear view

To RS-232C terminal

RS-232C serial control cable (cross type, commercially available)

Note

•The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the operation manual of the computer for details.

•Refer to ÒSETUP MANUALÓ contained on the supplied CD-ROM for the RS-232C specifications and commands.

Info

•Do not connect the RS-232C cable to a terminal other than the RS-232C terminal on the computer. This may damage your computer or projector.

•Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This may damage your computer.

When connecting to the LAN terminal using a LAN cable

Connections

Hub or computer

LINK LED (green)

Illuminates when linked.

TX/RX LED (yellow) Illuminates when transmitting/receiving data.

To LAN terminal

To LAN terminal

Rear view

*To ensure safety, do not connect the LAN terminal with any cables such as a telephone line that may cause excessive voltage.

Note

LAN cable

(Category 5 type, commercially available)

•When connecting to a hub, use straight-through Category 5 (CAT.5) type cable (commercially available).

•When connecting to a computer, use cross-over Category 5 (CAT.5) type cable (commercially available).

-27

Image 29

Contents XG-P610X Special Note for Users in the U.K Model No Serial NoIntroduction Product Disposal Operation Info Indicates safeguards when using the projectorButtons used in this Preparing ContentsReference Contents Setup ManualFor Macintosh¨ When you want to view the setup manualFor Windows¨ Accessories CleaningPower Sources Power-Cord ProtectionAvoid locations with extremes of tem- perature Rest your eyes occasionallyTemperature monitor function Using the projector in other countriesOptional lens installation Do not block the intake and exhaust ventsOptional accessories AccessoriesSupplied accessories Optional lenses AccessoriesThrow Distance Projector Part Names and FunctionsPart Names and Functions Projector Rear ViewMouse/adjustment button 18 47 //\ Remote ControlWhen using the remote control Using the Remote ControlUsable Range Inserting the BatteriesSwitching the Remote Control Mode Using the Remote Control with a Signal CableUsing the Remote Control Using the Remote Control as a Wireless Computer MouseSwitch on the remote con Trol to the Mouse position Use the mouse functionQuick Start Setup and ProjectionQuick Start Adjust the angleSetting Up the Projector Setting Up the ProjectorSignal Input Normal Mode Setting Up the ProjectorSignal Input Stretch Mode F2.5, f=25.5-32 mmSet to ÒFrontÓ Projecting a Reversed ImageTerminals on the Projector Connecting the Projector to Other EquipmentVideo equipment Video Connecting the Projector to Other EquipmentControlling the Projector by a Computer When connecting to the LAN terminal using a LAN cableTurning the Power Off Put Connecting the Power CordTurning the Projector On/Off Turning the Projector OnShifting the Lens Image ProjectionImage Projection Using the Adjustment FeetRotate the adjustment feet to adjust the projected angle Adjusting the Projected Image Size Adjusting the FocusZoom buttons Focus buttons Zoom buttonsKeystone button Adjustment Button //\ Press Keystone on the projector or on the remote controlCorrecting Trapezoidal Distortion Select the type of the keystone correctionGeometric Adjustment Keystone Press , , \ or to correct Adjustment withImage distortion Press Keystone to set the positionAdjusting the Volume Switching the Input ModeVolume buttons ButtonsTurning Off the Sound Temporarily Press Undo on the remote con- trol to cancel the operationDisplaying an Enlarged Portion of an Image Press Magnify on the re- mote controlPress Freeze on the remote control Selecting the Picture ModePress Picture Mode on the re- mote control Freeze button Undo button Picture Mode buttonMouse/adjustment button //\ Undo button Resize button Resize ModePress Resize on the remote control VIDEO/DTV About CopyrightsHiding the Projected Image Shutter function Displaying and Setting the Break TimerPressing Shutter Open will turn the projected image back on Shutter buttonsFollowing shows the items that can be set in the projector Menu ItemsVIDEO/S-VIDEO ÒC.M.S.Ó menu Menu ItemsÒAudioÓ menu Status menu Example ÒPictureÓ screen menu for COMPUTER1 RGB mode Using the Menu ScreenMenu Selections Press MenuPress or to select the item you want to adjust Using the Menu ScreenPress \ or to adjust the item selected Press EnterSelect a picture mode before adjusting the im- age Picture Adjustment Picture menuAdjusting the Image Make sure to set Òdnró to ÒOffÓ in the following cases Picture Adjustment ÒPictureÓ menuReducing Image Noise DNR When COMPUTER1/2 is selected for the input mode Selecting the Signal TypeWhen DVI is selected for the input mode Selecting the Dynamic RangeColor Management System C. M. S. menu Adjusting the Computer Image Computer Image Adjustment Fine Sync menuSaving Adjustment Settings Accessing Adjustment SettingsAuto Sync Adjustment Checking the Input SignalSetting the Auto Sync Display Function Computer Image Adjustment ÒFine SyncÓ menuAdjusting the Audio Audio Adjustment ÒAudioÓ menuSetting the Audio Output Type Setting the SpeakerDisplaying Dual Pictures Pict in Pict Using the ÒOptions 1Ó MenuSetting the Resize Mode Setting the Video System Setting On-screen DisplayShifting the Projected Image Vertically Digital Shift Capturing Projected ImagesSetting the Eco Mode Detecting the Input Signals AutomaticallySetting the Auto Power Off Function Selecting the Background ImageWhen the System Lock is set Setting the System Lock FunctionSelect System Lock on the Op- tions 1 menu, then press Enter the same keycode in Recon- firmEnter the same keycode in ÒRecon- firmÓ Using the ÒOptions 1Ó MenuSelect ÒPasswordÓ from the ÒOptions 2Ó menu, and press Setting a PasswordIf You Forget Your Password Controlling Multiple Projectors with the One Remote Control Setting the Lamp ModeHelpful Functions Set during Installation Options 2 menu Selecting the Lens TypeSelecting the Fan Mode Shortcut to Make Projector Stack SettingsSetting the Auto Restart Function Bypassing Unused Input SelectionsSetting the LAN/RS232C Setting the Monitor OutputSetting the Dhcp Client Helpful Functions Set during Installation ÒOptions 2Ó menuReturning to the Default Settings Setting the TCP/IP Service ModeOverview of All Menu Settings and the Lamp Life Selecting the On-screen Display LanguageCleaning the projector MaintenanceCleaning the air vents and the intake vent cover Cleaning the lensRemove the filter cover Cleaning and Replacing the Dust FiltersCleaning the Dust Filters Replace the filter cover Cleaning and Replacing the Dust FiltersReplacing the Dust Filters About the lamp indicator Maintenance IndicatorsAbout the temperature warning indicator Maintenance Indicators Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitRegarding the Lamp Remove the lamp unit User service screwInsert the new lamp unit Replace the lamp unit coverConnect the power cord Resetting the Lamp TimerReset the lamp timer Reset the lamp timer after replacing the lampComputer Computer Compatibility ChartDTV Computer Compatibility ChartRemove the lens cover Attaching the Optional LensSlide and attach the lens cover Attaching the Optional LensRemote control batteries have run out TroubleshootingSee Maintenance Indicators TroubleshootingFor Sharp Assistance Hdmi SpecificationsIndex Advanced intelligent compression All Reset Area zoomSharp Corporation