Sharp XG-P610X-N quick start Attaching the Optional Lens, Remove the lens cover

Page 79

Attaching the Optional Lens

Do not attempt to exchange the lens when the projector is installed hanging from the ceiling. Injury may occur if the lens cover and lens fall.

Before exchanging the lens, reset lens shift to the center position. (The lens shift is located at the center in the factory preset.)

When resetting the lens shift to the center position, press H&V LENS SHIFT and then press UNDO.

•The lens shift reset screen will be displayed. Select “Yes” to reset.

1 Press STANDBY on the projector or on the remote control to put the projector into standby mode.

•Disconnect the power cord and unplug the power cord from the AC socket after the cooling fan stops.

2 Remove the lens cover.

•Press the lens cover removal button (1). Slide the lens cover forward (2).

3 Turn the lens in the direction of the arrow while pressing the lens re- moval lever to pull the lens out.

STANDBY button

H&V LENS SHIFT

button

UNDO button

Power cord

Removal lever

Appendix

-77

Image 79

Contents XG-P610X Special Note for Users in the U.K Model No Serial NoIntroduction Product Disposal Buttons used in this Info Indicates safeguards when using the projectorOperation Preparing ContentsReference Contents Setup ManualFor Windows¨ When you want to view the setup manualFor Macintosh¨ Power-Cord Protection CleaningAccessories Power SourcesAvoid locations with extremes of tem- perature Rest your eyes occasionallyDo not block the intake and exhaust vents Using the projector in other countriesTemperature monitor function Optional lens installationSupplied accessories AccessoriesOptional accessories Throw Distance AccessoriesOptional lenses Projector Part Names and FunctionsPart Names and Functions Projector Rear ViewMouse/adjustment button 18 47 //\ Remote ControlInserting the Batteries Using the Remote ControlWhen using the remote control Usable RangeSwitching the Remote Control Mode Using the Remote Control with a Signal CableUse the mouse function Using the Remote Control as a Wireless Computer MouseUsing the Remote Control Switch on the remote con Trol to the Mouse positionQuick Start Setup and ProjectionQuick Start Adjust the angleSetting Up the Projector Setting Up the ProjectorF2.5, f=25.5-32 mm Setting Up the ProjectorSignal Input Normal Mode Signal Input Stretch ModeSet to ÒFrontÓ Projecting a Reversed ImageTerminals on the Projector Connecting the Projector to Other EquipmentVideo equipment Video Connecting the Projector to Other EquipmentControlling the Projector by a Computer When connecting to the LAN terminal using a LAN cableTurning the Projector On Connecting the Power CordTurning the Power Off Put Turning the Projector On/OffShifting the Lens Image ProjectionRotate the adjustment feet to adjust the projected angle Using the Adjustment FeetImage Projection Zoom buttons Adjusting the FocusAdjusting the Projected Image Size Zoom buttons Focus buttonsSelect the type of the keystone correction Press Keystone on the projector or on the remote controlKeystone button Adjustment Button //\ Correcting Trapezoidal DistortionGeometric Adjustment Keystone Press Keystone to set the position Adjustment withPress , , \ or to correct Image distortionButtons Switching the Input ModeAdjusting the Volume Volume buttonsPress Magnify on the re- mote control Press Undo on the remote con- trol to cancel the operationTurning Off the Sound Temporarily Displaying an Enlarged Portion of an ImageFreeze button Undo button Picture Mode button Selecting the Picture ModePress Freeze on the remote control Press Picture Mode on the re- mote controlPress Resize on the remote control Resize ModeMouse/adjustment button //\ Undo button Resize button VIDEO/DTV About CopyrightsShutter buttons Displaying and Setting the Break TimerHiding the Projected Image Shutter function Pressing Shutter Open will turn the projected image back onFollowing shows the items that can be set in the projector Menu ItemsVIDEO/S-VIDEO ÒC.M.S.Ó menu Menu ItemsÒAudioÓ menu Status menu Press Menu Using the Menu ScreenExample ÒPictureÓ screen menu for COMPUTER1 RGB mode Menu SelectionsPress Enter Using the Menu ScreenPress or to select the item you want to adjust Press \ or to adjust the item selectedAdjusting the Image Picture Adjustment Picture menuSelect a picture mode before adjusting the im- age Reducing Image Noise DNR Picture Adjustment ÒPictureÓ menuMake sure to set Òdnró to ÒOffÓ in the following cases Selecting the Dynamic Range Selecting the Signal TypeWhen COMPUTER1/2 is selected for the input mode When DVI is selected for the input modeColor Management System C. M. S. menu Accessing Adjustment Settings Computer Image Adjustment Fine Sync menuAdjusting the Computer Image Saving Adjustment SettingsComputer Image Adjustment ÒFine SyncÓ menu Checking the Input SignalAuto Sync Adjustment Setting the Auto Sync Display FunctionSetting the Speaker Audio Adjustment ÒAudioÓ menuAdjusting the Audio Setting the Audio Output TypeSetting the Resize Mode Using the ÒOptions 1Ó MenuDisplaying Dual Pictures Pict in Pict Capturing Projected Images Setting On-screen DisplaySetting the Video System Shifting the Projected Image Vertically Digital ShiftSelecting the Background Image Detecting the Input Signals AutomaticallySetting the Eco Mode Setting the Auto Power Off FunctionEnter the same keycode in Recon- firm Setting the System Lock FunctionWhen the System Lock is set Select System Lock on the Op- tions 1 menu, then pressEnter the same keycode in ÒRecon- firmÓ Using the ÒOptions 1Ó MenuIf You Forget Your Password Setting a PasswordSelect ÒPasswordÓ from the ÒOptions 2Ó menu, and press Selecting the Lens Type Setting the Lamp ModeControlling Multiple Projectors with the One Remote Control Helpful Functions Set during Installation Options 2 menuBypassing Unused Input Selections Shortcut to Make Projector Stack SettingsSelecting the Fan Mode Setting the Auto Restart FunctionHelpful Functions Set during Installation ÒOptions 2Ó menu Setting the Monitor OutputSetting the LAN/RS232C Setting the Dhcp ClientSelecting the On-screen Display Language Setting the TCP/IP Service ModeReturning to the Default Settings Overview of All Menu Settings and the Lamp LifeCleaning the lens MaintenanceCleaning the projector Cleaning the air vents and the intake vent coverCleaning the Dust Filters Cleaning and Replacing the Dust FiltersRemove the filter cover Replacing the Dust Filters Cleaning and Replacing the Dust FiltersReplace the filter cover About the temperature warning indicator Maintenance IndicatorsAbout the lamp indicator Maintenance Indicators Lamp Regarding the LampReplacing the Lamp Regarding the Lamp Removing and Installing the Lamp UnitRemove the lamp unit cover Replace the lamp unit cover User service screwRemove the lamp unit Insert the new lamp unitReset the lamp timer after replacing the lamp Resetting the Lamp TimerConnect the power cord Reset the lamp timerComputer Computer Compatibility ChartDTV Computer Compatibility ChartRemove the lens cover Attaching the Optional LensSlide and attach the lens cover Attaching the Optional LensRemote control batteries have run out TroubleshootingSee Maintenance Indicators TroubleshootingFor Sharp Assistance Hdmi SpecificationsIndex Advanced intelligent compression All Reset Area zoomSharp Corporation