Sharp XG-P610X-N quick start Troubleshooting, Remote control batteries have run out

Page 81

Troubleshooting

 

Problem

Check

Page

 

 

 

• Projector power cord is not plugged into the wall outlet.

28

 

 

 

• Power to the external connected devices is off.

—

 

 

 

• The selected input mode is wrong.

36

 

 

 

• Cables are incorrectly connected to the projector.

24–27

 

 

 

 

 

 

• Remote control batteries have run out.

16

 

 

 

• External output has not been set when connecting notebook computer.

24

 

 

 

• When the connected DVI digital equipment is turned on before the

 

 

 

 

“DVI” input mode is selected on the projector, the image may not be

 

No picture and no sound

 

projected properly or may not be displayed at all. Ensure that the

 

or projector does not start.

appropriate input mode has been selected and set the input signal type

 

 

 

 

on the projector before you turn on the connected equipment.

 

 

 

 

• Is the lens cover correctly attached?

78

 

 

 

• Is the filter cover correctly attached?

68

 

 

 

• Is the lamp unit cover correctly attached?

73

 

 

 

• Cables are incorrectly connected to the projector.

24–27

 

 

 

 

 

 

• “Bright” is set to minimum position.

49

 

 

 

• The “Shutter” is closed.

41

 

 

 

 

 

Sound is heard but no

 

 

picture appears.

 

 

 

 

 

 

 

 

 

 

• Image adjustments are incorrectly set.

49

 

 

 

 

 

 

(COMPUTER 1/2, DVI, HDMI only)

 

 

 

 

• Input signal type (RGB/Component) is incorrectly set.

51

 

 

 

(VIDEO, S-VIDEO only)

57

 

 

 

• Video Input system is incorrectly set.

Color is faded or poor.

 

 

 

 

 

 

 

 

 

 

• Adjust the focus.

31

 

 

 

• The projection distance exceeds the focus range.

22

 

 

 

• When an optional lens is attached, refer to the operation

 

 

 

 

manual of the lens.

 

 

 

 

• There is fog on the lens. If the projector is carried from a cold

—

 

 

 

room into a warm room, or if it is suddenly heated, condensation

 

 

 

 

 

 

 

 

may form on the surface of the lens and the image will become

 

 

 

 

blurred. Please set up the projector at least one hour before it is

 

 

 

 

to be used. If condensation should form, remove the power cord

 

 

 

 

from the wall outlet and wait for it to clear.

 

 

 

 

 

Picture is blurred;

(Computer Input only)

53

 

noise appears.

• Perform “Fine Sync” Adjustments. (“Clock” Adjustment)

 

53

 

 

 

• Perform “Fine Sync” Adjustments. (“Phase” Adjustment)

 

 

 

• Turn off the LCD display of the notebook computer.

76

 

 

 

• Noise may appear depending on the computer.

—

 

 

 

• The “DNR” (Digital Noise Reduction) setting is not correct.

50

 

 

 

• Cables are incorrectly connected to the projector.

24–27

 

 

 

 

 

 

• Volume is set to minimum.

36

 

 

 

• The “MUTE” function is working.

37

 

 

 

• The “Speaker” menu is set to “Off”.

55

Picture appears but no

 

 

sound is heard.

 

 

 

 

 

 

 

Appendix

-79

Page 80 Page 82
Image 81
Page 80 Page 82
Contents XG-P610X Special Note for Users in the U.K Model No Serial NoIntroduction Product Disposal Info Indicates safeguards when using the projector Buttons used in thisOperation Preparing ContentsReference Contents Setup ManualWhen you want to view the setup manual For Windows¨For Macintosh¨ Accessories CleaningPower Sources Power-Cord ProtectionAvoid locations with extremes of tem- perature Rest your eyes occasionallyTemperature monitor function Using the projector in other countriesOptional lens installation Do not block the intake and exhaust ventsAccessories Supplied accessoriesOptional accessories Accessories Throw DistanceOptional lenses Projector Part Names and FunctionsPart Names and Functions Projector Rear ViewMouse/adjustment button 18 47 //\ Remote ControlWhen using the remote control Using the Remote ControlUsable Range Inserting the BatteriesSwitching the Remote Control Mode Using the Remote Control with a Signal CableUsing the Remote Control Using the Remote Control as a Wireless Computer MouseSwitch on the remote con Trol to the Mouse position Use the mouse functionQuick Start Setup and ProjectionQuick Start Adjust the angleSetting Up the Projector Setting Up the ProjectorSignal Input Normal Mode Setting Up the ProjectorSignal Input Stretch Mode F2.5, f=25.5-32 mmSet to ÒFrontÓ Projecting a Reversed ImageTerminals on the Projector Connecting the Projector to Other EquipmentVideo equipment Video Connecting the Projector to Other EquipmentControlling the Projector by a Computer When connecting to the LAN terminal using a LAN cableTurning the Power Off Put Connecting the Power CordTurning the Projector On/Off Turning the Projector OnShifting the Lens Image ProjectionUsing the Adjustment Feet Rotate the adjustment feet to adjust the projected angleImage Projection Adjusting the Projected Image Size Adjusting the FocusZoom buttons Focus buttons Zoom buttonsKeystone button Adjustment Button //\ Press Keystone on the projector or on the remote controlCorrecting Trapezoidal Distortion Select the type of the keystone correctionGeometric Adjustment Keystone Press , , \ or to correct Adjustment withImage distortion Press Keystone to set the positionAdjusting the Volume Switching the Input ModeVolume buttons ButtonsTurning Off the Sound Temporarily Press Undo on the remote con- trol to cancel the operationDisplaying an Enlarged Portion of an Image Press Magnify on the re- mote controlPress Freeze on the remote control Selecting the Picture ModePress Picture Mode on the re- mote control Freeze button Undo button Picture Mode buttonResize Mode Press Resize on the remote controlMouse/adjustment button //\ Undo button Resize button VIDEO/DTV About CopyrightsHiding the Projected Image Shutter function Displaying and Setting the Break TimerPressing Shutter Open will turn the projected image back on Shutter buttonsFollowing shows the items that can be set in the projector Menu ItemsVIDEO/S-VIDEO ÒC.M.S.Ó menu Menu ItemsÒAudioÓ menu Status menu Example ÒPictureÓ screen menu for COMPUTER1 RGB mode Using the Menu ScreenMenu Selections Press MenuPress or to select the item you want to adjust Using the Menu ScreenPress \ or to adjust the item selected Press EnterPicture Adjustment Picture menu Adjusting the ImageSelect a picture mode before adjusting the im- age Picture Adjustment ÒPictureÓ menu Reducing Image Noise DNRMake sure to set Òdnró to ÒOffÓ in the following cases When COMPUTER1/2 is selected for the input mode Selecting the Signal TypeWhen DVI is selected for the input mode Selecting the Dynamic RangeColor Management System C. M. S. menu Adjusting the Computer Image Computer Image Adjustment Fine Sync menuSaving Adjustment Settings Accessing Adjustment SettingsAuto Sync Adjustment Checking the Input SignalSetting the Auto Sync Display Function Computer Image Adjustment ÒFine SyncÓ menuAdjusting the Audio Audio Adjustment ÒAudioÓ menuSetting the Audio Output Type Setting the SpeakerUsing the ÒOptions 1Ó Menu Setting the Resize ModeDisplaying Dual Pictures Pict in Pict Setting the Video System Setting On-screen DisplayShifting the Projected Image Vertically Digital Shift Capturing Projected ImagesSetting the Eco Mode Detecting the Input Signals AutomaticallySetting the Auto Power Off Function Selecting the Background ImageWhen the System Lock is set Setting the System Lock FunctionSelect System Lock on the Op- tions 1 menu, then press Enter the same keycode in Recon- firmEnter the same keycode in ÒRecon- firmÓ Using the ÒOptions 1Ó MenuSetting a Password If You Forget Your PasswordSelect ÒPasswordÓ from the ÒOptions 2Ó menu, and press Controlling Multiple Projectors with the One Remote Control Setting the Lamp ModeHelpful Functions Set during Installation Options 2 menu Selecting the Lens TypeSelecting the Fan Mode Shortcut to Make Projector Stack SettingsSetting the Auto Restart Function Bypassing Unused Input SelectionsSetting the LAN/RS232C Setting the Monitor OutputSetting the Dhcp Client Helpful Functions Set during Installation ÒOptions 2Ó menuReturning to the Default Settings Setting the TCP/IP Service ModeOverview of All Menu Settings and the Lamp Life Selecting the On-screen Display LanguageCleaning the projector MaintenanceCleaning the air vents and the intake vent cover Cleaning the lensCleaning and Replacing the Dust Filters Cleaning the Dust FiltersRemove the filter cover Cleaning and Replacing the Dust Filters Replacing the Dust FiltersReplace the filter cover Maintenance Indicators About the temperature warning indicatorAbout the lamp indicator Maintenance Indicators Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Regarding the LampRemove the lamp unit cover Remove the lamp unit User service screwInsert the new lamp unit Replace the lamp unit coverConnect the power cord Resetting the Lamp TimerReset the lamp timer Reset the lamp timer after replacing the lampComputer Computer Compatibility ChartDTV Computer Compatibility ChartRemove the lens cover Attaching the Optional LensSlide and attach the lens cover Attaching the Optional LensRemote control batteries have run out TroubleshootingSee Maintenance Indicators TroubleshootingFor Sharp Assistance Hdmi SpecificationsIndex Advanced intelligent compression All Reset Area zoomSharp Corporation
Top Page Image Contents