Sharp XG-P610X-N Remove the lamp unit, Insert the new lamp unit, Replace the lamp unit cover

Page 75

3Remove the lamp unit.

•Loosen the securing screws (two for each lamp) from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.

4Insert the new lamp unit.

•Fully insert the lamp unit into the lamp unit compartment. Press the handles back to their positions, and tighten the securing screws.

5Replace the lamp unit cover.

•Slide the lamp unit cover to the position where the indicator “” of the lamp cover unit and the “\” of the projector will meet to close the cover. Then tighten the user service screw to secure the lamp unit cover.

Info

•If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Securing screws

Handle

Compartment

for

Lamp 2 Compartment

for Lamp 1

AN-P610LP

User service screw

Appendix

-73

Image 75

Contents XG-P610X Special Note for Users in the U.K Model No Serial NoIntroduction Product Disposal Info Indicates safeguards when using the projector Buttons used in thisOperation Preparing ContentsReference Contents Setup ManualWhen you want to view the setup manual For Windows¨For Macintosh¨ Power-Cord Protection CleaningAccessories Power SourcesAvoid locations with extremes of tem- perature Rest your eyes occasionallyDo not block the intake and exhaust vents Using the projector in other countriesTemperature monitor function Optional lens installationAccessories Supplied accessoriesOptional accessories Accessories Throw DistanceOptional lenses Projector Part Names and FunctionsPart Names and Functions Projector Rear ViewMouse/adjustment button 18 47 //\ Remote ControlInserting the Batteries Using the Remote ControlWhen using the remote control Usable RangeSwitching the Remote Control Mode Using the Remote Control with a Signal CableUse the mouse function Using the Remote Control as a Wireless Computer MouseUsing the Remote Control Switch on the remote con Trol to the Mouse positionQuick Start Setup and ProjectionQuick Start Adjust the angleSetting Up the Projector Setting Up the ProjectorF2.5, f=25.5-32 mm Setting Up the ProjectorSignal Input Normal Mode Signal Input Stretch ModeSet to ÒFrontÓ Projecting a Reversed ImageTerminals on the Projector Connecting the Projector to Other EquipmentVideo equipment Video Connecting the Projector to Other EquipmentControlling the Projector by a Computer When connecting to the LAN terminal using a LAN cableTurning the Projector On Connecting the Power CordTurning the Power Off Put Turning the Projector On/OffShifting the Lens Image ProjectionUsing the Adjustment Feet Rotate the adjustment feet to adjust the projected angleImage Projection Zoom buttons Adjusting the FocusAdjusting the Projected Image Size Zoom buttons Focus buttonsSelect the type of the keystone correction Press Keystone on the projector or on the remote controlKeystone button Adjustment Button //\ Correcting Trapezoidal DistortionGeometric Adjustment Keystone Press Keystone to set the position Adjustment withPress , , \ or to correct Image distortionButtons Switching the Input ModeAdjusting the Volume Volume buttonsPress Magnify on the re- mote control Press Undo on the remote con- trol to cancel the operationTurning Off the Sound Temporarily Displaying an Enlarged Portion of an ImageFreeze button Undo button Picture Mode button Selecting the Picture ModePress Freeze on the remote control Press Picture Mode on the re- mote controlResize Mode Press Resize on the remote controlMouse/adjustment button //\ Undo button Resize button VIDEO/DTV About CopyrightsShutter buttons Displaying and Setting the Break TimerHiding the Projected Image Shutter function Pressing Shutter Open will turn the projected image back onFollowing shows the items that can be set in the projector Menu ItemsVIDEO/S-VIDEO ÒC.M.S.Ó menu Menu ItemsÒAudioÓ menu Status menu Press Menu Using the Menu ScreenExample ÒPictureÓ screen menu for COMPUTER1 RGB mode Menu SelectionsPress Enter Using the Menu ScreenPress or to select the item you want to adjust Press \ or to adjust the item selectedPicture Adjustment Picture menu Adjusting the ImageSelect a picture mode before adjusting the im- age Picture Adjustment ÒPictureÓ menu Reducing Image Noise DNRMake sure to set Òdnró to ÒOffÓ in the following cases Selecting the Dynamic Range Selecting the Signal TypeWhen COMPUTER1/2 is selected for the input mode When DVI is selected for the input modeColor Management System C. M. S. menu Accessing Adjustment Settings Computer Image Adjustment Fine Sync menuAdjusting the Computer Image Saving Adjustment SettingsComputer Image Adjustment ÒFine SyncÓ menu Checking the Input SignalAuto Sync Adjustment Setting the Auto Sync Display FunctionSetting the Speaker Audio Adjustment ÒAudioÓ menuAdjusting the Audio Setting the Audio Output TypeUsing the ÒOptions 1Ó Menu Setting the Resize ModeDisplaying Dual Pictures Pict in Pict Capturing Projected Images Setting On-screen DisplaySetting the Video System Shifting the Projected Image Vertically Digital ShiftSelecting the Background Image Detecting the Input Signals AutomaticallySetting the Eco Mode Setting the Auto Power Off FunctionEnter the same keycode in Recon- firm Setting the System Lock FunctionWhen the System Lock is set Select System Lock on the Op- tions 1 menu, then pressEnter the same keycode in ÒRecon- firmÓ Using the ÒOptions 1Ó MenuSetting a Password If You Forget Your PasswordSelect ÒPasswordÓ from the ÒOptions 2Ó menu, and press Selecting the Lens Type Setting the Lamp ModeControlling Multiple Projectors with the One Remote Control Helpful Functions Set during Installation Options 2 menuBypassing Unused Input Selections Shortcut to Make Projector Stack SettingsSelecting the Fan Mode Setting the Auto Restart FunctionHelpful Functions Set during Installation ÒOptions 2Ó menu Setting the Monitor OutputSetting the LAN/RS232C Setting the Dhcp ClientSelecting the On-screen Display Language Setting the TCP/IP Service ModeReturning to the Default Settings Overview of All Menu Settings and the Lamp LifeCleaning the lens MaintenanceCleaning the projector Cleaning the air vents and the intake vent coverCleaning and Replacing the Dust Filters Cleaning the Dust FiltersRemove the filter cover Cleaning and Replacing the Dust Filters Replacing the Dust FiltersReplace the filter cover Maintenance Indicators About the temperature warning indicatorAbout the lamp indicator Maintenance Indicators Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Regarding the LampRemove the lamp unit cover Replace the lamp unit cover User service screwRemove the lamp unit Insert the new lamp unitReset the lamp timer after replacing the lamp Resetting the Lamp TimerConnect the power cord Reset the lamp timerComputer Computer Compatibility ChartDTV Computer Compatibility ChartRemove the lens cover Attaching the Optional LensSlide and attach the lens cover Attaching the Optional LensRemote control batteries have run out TroubleshootingSee Maintenance Indicators TroubleshootingFor Sharp Assistance Hdmi SpecificationsIndex Advanced intelligent compression All Reset Area zoomSharp Corporation