Sharp XG-P610X-N quick start Removing and Installing the Lamp Unit, Regarding the Lamp

Page 74

Regarding the Lamp

Removing and Installing the Lamp Unit

Warning!

•Do not remove the lamp unit from the pro- jector right after use. The lamp and parts around the lamp will be very hot and may cause burn or injury.

Info

•Make sure the lamp unit is removed using the handle. Make sure the glass surface of the lamp unit or the inside of the projector are not touched.

•To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

1Press STANDBY on the projec- tor or on the remote control to put the projector into standby mode.

•Disconnect the power cord and unplug the power cord from the AC socket after the cooling fan stops.

•The cooling fan may continue to run for a while even after the power cord is re- moved.

•Leave the lamp until it has fully cooled down (about 1 hour).

2Remove the lamp unit cover.

•Loosen the user service screw (1) that secures the lamp unit cover. Remove the

lamp unit cover to slide it in the direc- tion of the arrow (2).

Optional	Lamp unit
accessory	AN-P610LP

STANDBY button

Power cord

2

1

User service screw

-72

Image 74

Contents XG-P610X Model No Serial No Special Note for Users in the U.KIntroduction Product Disposal Operation Info Indicates safeguards when using the projectorButtons used in this Contents PreparingReference Setup Manual ContentsFor Macintosh¨ When you want to view the setup manualFor Windows¨ Power Sources CleaningAccessories Power-Cord ProtectionRest your eyes occasionally Avoid locations with extremes of tem- peratureOptional lens installation Using the projector in other countriesTemperature monitor function Do not block the intake and exhaust ventsOptional accessories AccessoriesSupplied accessories Optional lenses AccessoriesThrow Distance Part Names and Functions ProjectorProjector Rear View Part Names and FunctionsRemote Control Mouse/adjustment button 18 47 //\Usable Range Using the Remote ControlWhen using the remote control Inserting the BatteriesUsing the Remote Control with a Signal Cable Switching the Remote Control ModeSwitch on the remote con Trol to the Mouse position Using the Remote Control as a Wireless Computer MouseUsing the Remote Control Use the mouse functionSetup and Projection Quick StartAdjust the angle Quick StartSetting Up the Projector Setting Up the ProjectorSignal Input Stretch Mode Setting Up the ProjectorSignal Input Normal Mode F2.5, f=25.5-32 mmProjecting a Reversed Image Set to ÒFrontÓConnecting the Projector to Other Equipment Terminals on the ProjectorVideo equipment Connecting the Projector to Other Equipment VideoWhen connecting to the LAN terminal using a LAN cable Controlling the Projector by a ComputerTurning the Projector On/Off Connecting the Power CordTurning the Power Off Put Turning the Projector OnImage Projection Shifting the LensImage Projection Using the Adjustment FeetRotate the adjustment feet to adjust the projected angle Zoom buttons Focus buttons Adjusting the FocusAdjusting the Projected Image Size Zoom buttonsCorrecting Trapezoidal Distortion Press Keystone on the projector or on the remote controlKeystone button Adjustment Button //\ Select the type of the keystone correctionGeometric Adjustment Keystone Image distortion Adjustment withPress , , \ or to correct Press Keystone to set the positionVolume buttons Switching the Input ModeAdjusting the Volume ButtonsDisplaying an Enlarged Portion of an Image Press Undo on the remote con- trol to cancel the operationTurning Off the Sound Temporarily Press Magnify on the re- mote controlPress Picture Mode on the re- mote control Selecting the Picture ModePress Freeze on the remote control Freeze button Undo button Picture Mode buttonMouse/adjustment button //\ Undo button Resize button Resize ModePress Resize on the remote control About Copyrights VIDEO/DTVPressing Shutter Open will turn the projected image back on Displaying and Setting the Break TimerHiding the Projected Image Shutter function Shutter buttonsMenu Items Following shows the items that can be set in the projectorVIDEO/S-VIDEO Menu Items ÒC.M.S.Ó menuÒAudioÓ menu Status menu Menu Selections Using the Menu ScreenExample ÒPictureÓ screen menu for COMPUTER1 RGB mode Press MenuPress \ or to adjust the item selected Using the Menu ScreenPress or to select the item you want to adjust Press EnterSelect a picture mode before adjusting the im- age Picture Adjustment Picture menuAdjusting the Image Make sure to set Òdnró to ÒOffÓ in the following cases Picture Adjustment ÒPictureÓ menuReducing Image Noise DNR When DVI is selected for the input mode Selecting the Signal TypeWhen COMPUTER1/2 is selected for the input mode Selecting the Dynamic RangeColor Management System C. M. S. menu Saving Adjustment Settings Computer Image Adjustment Fine Sync menuAdjusting the Computer Image Accessing Adjustment SettingsSetting the Auto Sync Display Function Checking the Input SignalAuto Sync Adjustment Computer Image Adjustment ÒFine SyncÓ menuSetting the Audio Output Type Audio Adjustment ÒAudioÓ menuAdjusting the Audio Setting the SpeakerDisplaying Dual Pictures Pict in Pict Using the ÒOptions 1Ó MenuSetting the Resize Mode Shifting the Projected Image Vertically Digital Shift Setting On-screen DisplaySetting the Video System Capturing Projected ImagesSetting the Auto Power Off Function Detecting the Input Signals AutomaticallySetting the Eco Mode Selecting the Background ImageSelect System Lock on the Op- tions 1 menu, then press Setting the System Lock FunctionWhen the System Lock is set Enter the same keycode in Recon- firmUsing the ÒOptions 1Ó Menu Enter the same keycode in ÒRecon- firmÓSelect ÒPasswordÓ from the ÒOptions 2Ó menu, and press Setting a PasswordIf You Forget Your Password Helpful Functions Set during Installation Options 2 menu Setting the Lamp ModeControlling Multiple Projectors with the One Remote Control Selecting the Lens TypeSetting the Auto Restart Function Shortcut to Make Projector Stack SettingsSelecting the Fan Mode Bypassing Unused Input SelectionsSetting the Dhcp Client Setting the Monitor OutputSetting the LAN/RS232C Helpful Functions Set during Installation ÒOptions 2Ó menuOverview of All Menu Settings and the Lamp Life Setting the TCP/IP Service ModeReturning to the Default Settings Selecting the On-screen Display LanguageCleaning the air vents and the intake vent cover MaintenanceCleaning the projector Cleaning the lensRemove the filter cover Cleaning and Replacing the Dust FiltersCleaning the Dust Filters Replace the filter cover Cleaning and Replacing the Dust FiltersReplacing the Dust Filters About the lamp indicator Maintenance IndicatorsAbout the temperature warning indicator Maintenance Indicators Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitRegarding the Lamp Insert the new lamp unit User service screwRemove the lamp unit Replace the lamp unit coverReset the lamp timer Resetting the Lamp TimerConnect the power cord Reset the lamp timer after replacing the lampComputer Compatibility Chart ComputerComputer Compatibility Chart DTVAttaching the Optional Lens Remove the lens coverAttaching the Optional Lens Slide and attach the lens coverTroubleshooting Remote control batteries have run outTroubleshooting See Maintenance IndicatorsFor Sharp Assistance Specifications HdmiAdvanced intelligent compression All Reset Area zoom IndexSharp Corporation