Sharp XG-P610X-N Cleaning and Replacing the Dust Filters, Replace the filter cover

Page 70

Cleaning and Replacing the Dust Filters

4 Replace the filter cover.

•Insert the filter cover as shown in the figure and push both the two tabs until you hear a click.

Note

•Be sure the filter cover is securely installed. The power will not turn on unless it is cor- rectly installed.

Replacing the Dust Filters

Info

•If the filters become too dirty to clean effec- tively, purchase new ones (9NK3243101400) from your nearest Sharp Authorized Projec- tor Dealer or Service Center.

After removing the filter cover (see step 2 of “Cleaning the Dust Filters”), remove the dust filters, then replace with new ones.

•Pick the dust filters up with your fingers and lift them out of the filter cover.

•When attaching the dust filters, make sure that these are inserted below the tabs on both left and right, and that the slits are pierced through.

Remove

Attach

Pierced through the nine slits.

Insert the filter below the six tabs on both left and right sides.

-68

Image 70

Contents XG-P610X Model No Serial No Special Note for Users in the U.KIntroduction Product Disposal Buttons used in this Info Indicates safeguards when using the projectorOperation Contents PreparingReference Setup Manual ContentsFor Windows¨ When you want to view the setup manualFor Macintosh¨ Power Sources CleaningAccessories Power-Cord ProtectionRest your eyes occasionally Avoid locations with extremes of tem- peratureOptional lens installation Using the projector in other countriesTemperature monitor function Do not block the intake and exhaust ventsSupplied accessories AccessoriesOptional accessories Throw Distance AccessoriesOptional lenses Part Names and Functions ProjectorProjector Rear View Part Names and FunctionsRemote Control Mouse/adjustment button 18 47 //\Usable Range Using the Remote ControlWhen using the remote control Inserting the BatteriesUsing the Remote Control with a Signal Cable Switching the Remote Control ModeSwitch on the remote con Trol to the Mouse position Using the Remote Control as a Wireless Computer MouseUsing the Remote Control Use the mouse functionSetup and Projection Quick StartAdjust the angle Quick StartSetting Up the Projector Setting Up the ProjectorSignal Input Stretch Mode Setting Up the ProjectorSignal Input Normal Mode F2.5, f=25.5-32 mmProjecting a Reversed Image Set to ÒFrontÓConnecting the Projector to Other Equipment Terminals on the ProjectorVideo equipment Connecting the Projector to Other Equipment VideoWhen connecting to the LAN terminal using a LAN cable Controlling the Projector by a ComputerTurning the Projector On/Off Connecting the Power CordTurning the Power Off Put Turning the Projector OnImage Projection Shifting the LensRotate the adjustment feet to adjust the projected angle Using the Adjustment FeetImage Projection Zoom buttons Focus buttons Adjusting the FocusAdjusting the Projected Image Size Zoom buttonsCorrecting Trapezoidal Distortion Press Keystone on the projector or on the remote controlKeystone button Adjustment Button //\ Select the type of the keystone correctionGeometric Adjustment Keystone Image distortion Adjustment withPress , , \ or to correct Press Keystone to set the positionVolume buttons Switching the Input ModeAdjusting the Volume ButtonsDisplaying an Enlarged Portion of an Image Press Undo on the remote con- trol to cancel the operationTurning Off the Sound Temporarily Press Magnify on the re- mote controlPress Picture Mode on the re- mote control Selecting the Picture ModePress Freeze on the remote control Freeze button Undo button Picture Mode buttonPress Resize on the remote control Resize ModeMouse/adjustment button //\ Undo button Resize button About Copyrights VIDEO/DTVPressing Shutter Open will turn the projected image back on Displaying and Setting the Break TimerHiding the Projected Image Shutter function Shutter buttonsMenu Items Following shows the items that can be set in the projectorVIDEO/S-VIDEO Menu Items ÒC.M.S.Ó menuÒAudioÓ menu Status menu Menu Selections Using the Menu ScreenExample ÒPictureÓ screen menu for COMPUTER1 RGB mode Press MenuPress \ or to adjust the item selected Using the Menu ScreenPress or to select the item you want to adjust Press EnterAdjusting the Image Picture Adjustment Picture menuSelect a picture mode before adjusting the im- age Reducing Image Noise DNR Picture Adjustment ÒPictureÓ menuMake sure to set Òdnró to ÒOffÓ in the following cases When DVI is selected for the input mode Selecting the Signal TypeWhen COMPUTER1/2 is selected for the input mode Selecting the Dynamic RangeColor Management System C. M. S. menu Saving Adjustment Settings Computer Image Adjustment Fine Sync menuAdjusting the Computer Image Accessing Adjustment SettingsSetting the Auto Sync Display Function Checking the Input SignalAuto Sync Adjustment Computer Image Adjustment ÒFine SyncÓ menuSetting the Audio Output Type Audio Adjustment ÒAudioÓ menuAdjusting the Audio Setting the SpeakerSetting the Resize Mode Using the ÒOptions 1Ó MenuDisplaying Dual Pictures Pict in Pict Shifting the Projected Image Vertically Digital Shift Setting On-screen DisplaySetting the Video System Capturing Projected ImagesSetting the Auto Power Off Function Detecting the Input Signals AutomaticallySetting the Eco Mode Selecting the Background ImageSelect System Lock on the Op- tions 1 menu, then press Setting the System Lock FunctionWhen the System Lock is set Enter the same keycode in Recon- firmUsing the ÒOptions 1Ó Menu Enter the same keycode in ÒRecon- firmÓIf You Forget Your Password Setting a PasswordSelect ÒPasswordÓ from the ÒOptions 2Ó menu, and press Helpful Functions Set during Installation Options 2 menu Setting the Lamp ModeControlling Multiple Projectors with the One Remote Control Selecting the Lens TypeSetting the Auto Restart Function Shortcut to Make Projector Stack SettingsSelecting the Fan Mode Bypassing Unused Input SelectionsSetting the Dhcp Client Setting the Monitor OutputSetting the LAN/RS232C Helpful Functions Set during Installation ÒOptions 2Ó menuOverview of All Menu Settings and the Lamp Life Setting the TCP/IP Service ModeReturning to the Default Settings Selecting the On-screen Display LanguageCleaning the air vents and the intake vent cover MaintenanceCleaning the projector Cleaning the lensCleaning the Dust Filters Cleaning and Replacing the Dust FiltersRemove the filter cover Replacing the Dust Filters Cleaning and Replacing the Dust FiltersReplace the filter cover About the temperature warning indicator Maintenance IndicatorsAbout the lamp indicator Maintenance Indicators Lamp Regarding the LampReplacing the Lamp Regarding the Lamp Removing and Installing the Lamp UnitRemove the lamp unit cover Insert the new lamp unit User service screwRemove the lamp unit Replace the lamp unit coverReset the lamp timer Resetting the Lamp TimerConnect the power cord Reset the lamp timer after replacing the lampComputer Compatibility Chart ComputerComputer Compatibility Chart DTVAttaching the Optional Lens Remove the lens coverAttaching the Optional Lens Slide and attach the lens coverTroubleshooting Remote control batteries have run outTroubleshooting See Maintenance IndicatorsFor Sharp Assistance Specifications HdmiAdvanced intelligent compression All Reset Area zoom IndexSharp Corporation