TANDBERG D12155-10 Audio Outputs, Level Settings Out1 +13.5dB Out2AUX Out3VCR Previous Menu

Page 60

Advanced use

TANDBERG Videoconferencing System

Audio Outputs

Audio out 1 is intended for connection to televisions or audio amplifiers.

Audio out 2 is intended for connection to audio recording equipment or to a telephone add-on hybrid. The signal is a mix of audio from both the far end and local end (not from Audio in 3).

Audio out 3 is intended for connection to a VCR or other recording equipment. The signal is a mix of audio from far end and local end (not from Audio in 4).

NOTE

NEVER CONNECT AUDIO OUT 2 OR AUDIO OUT 3 TO A LOUDSPEAKER PLACED IN THE SAME ROOM AS THE MICROPHONES CONNECTED TO THE SYSTEM. DOING THIS WILL CAUSE HOWLINGAND POSSIBLE DAMAGE TO THE SPEAKER SYSTEM.

If an output is ‘Off’, no audio will be sent to that output.

Level Settings - Outputs

Level Settings

 

 

Out1:

+13.5dB

Out2(AUX):

— +13.5dB

Out3(VCR):

+13.5dB

Previous Menu

 

 

Adjust the audio output levels according to the parameters of the external audio equipment connected. These levels should only be adjusted when installing new audio equipment. The default settings are correct for the TANDBERG Natural Audio module and for most consumer electronics devices (televisions, VCRs, etc.).

The volume keys on the remote control adjust the level of output 1 (the speaker output). The volume control has no effect on outputs 2 and 3.

60

Image 60
Contents UserManual Tandberg Videoconferencing System Environmental Issues Trademarks and copyrightOperator Safety Summary Contents Advanced use Peripheral EquipmentAppendices 104 Index 114 Introduction TIPMenu structure LANTandberg 2500 Videoconferencing System At a glance the Tandberg 2500 systemV.E. II Camera MonitorsCodec Remote control CabinetTable microphone Installation PrecautionsUnpacking Page Connecting cables Power cableMonitor cables Microphone cableMonitor configuration 5a. Isdn cables using BRI interface5b. Other networks using the External Network interface LAN cableSystem configuration MenuIsdn configuration LAN configuration Getting started System start-upWelcome menu Basics Making and ending calls Making a callTIP Selecting / setting default quality bandwidth Selecting / setting default network Answer a call End a callCorrecting keying mistakes Directory Press D Irectory to bring up the following menuAdd New Entry Edit EntryDelete Entry Add MultiSite Entry Add SiteAdjusting volume General useView outgoing video selfview Microphone on/offDo Not Disturb / Sleep Mode On Screen SymbolsFocusing camera Controlling the Main CameraSelecting video sources Moving / zooming cameraVoice Activated Camera Positioning Presets Selecting presetsStoring presets Far end camera control Fecc Sending and receiving snapshots Sending a snapshotViewing a snapshot Receiving a snapshotDuo Video Add Duo VideoEnd a Duo Video call MultiSite MCU Establishing MultiSite meetings using Directory MultiSite cascadingAdding an extra site dial out Disconnecting sites from a conference Adding an extra site dialPC Presenter PC SoftPresenterWeb-interface Text Chat / Closed CaptioningOther PC applications StreamingSnapshots Menu Password Advanced useMain menu Call quality Advanced call quality QcifPresentation Mode Duo Video ModePresentations Duo Video QualityDuo Video Number Duo Video / Snapshot SourceAuto-Display Snapshot Snapshot FilterUtilities AutoanswerFar end camera control Dual MonitorAuto-PIP Welcome MenuContinuous Presence MCU status lineWeb Snapshots MCU services Quick Menu Request floor Release floorTerminal Names View site #Chair control Audio Settings Audio InputsPage Level Settings Out1 +13.5dB Out2AUX Out3VCR Previous Menu Audio OutputsEcho Control Page Automatic Gain Control AGC Settings Alert Tones & Volume Restore Audio DefaultsVideo Settings Camera Tracking ModeDocument Camera Focus BrightnessWhitebalance Video NameVGA Settings VNC Settings Terminal Settings Network ConfigurationISDN-BRI Settings Spids This Service has Limited Access on Some Isdn Networks Parallel dial External network settings 35/RS-366 cable LAN Settings Page Settings Page Advanced H.323 Settings RsvpQoS Type IP PrecedenceDiffserv IP Settings Snmp Settings Call Settings Access CodeIncoming MCU calls Incoming telephone callsEncryption Mode Encryption Secure ConferenceMax Call Length Network ProfilesDataport configuration Page Language Software OptionsDiagnostics System infoChannel status TIP Restore defaults Call statusView current settings Test subsystemIP Address Conflict Check Peripheral Equipment InterfacesE2 only Dual Monitor XGA monitorDocument camera Multiple controllable cameras AudioScience microphone TrackerVideo Cassette Recorder VCR VCR PlaybackVCR Recording Telephone Add-On Extra fixed camerasPC applications Additional microphones Appendices TandbergAppendix 2 Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adapterLoudspeaker volume Appendix 3 Environmental considerationsIris control and lighting BackgroundGuidelines for setting up videoconferencing rooms How to prepare a typical room for videoconferencingAppendix 4 Using the file system Custom logos · Go to the folder where your logo is located Appendix 6 Security ABC111 112 Appendix 6 Declaration of Conformity Index FeccTandberg Videoconferencing System Index Current settings 93 outgoing video 30 Viewing a still image