TANDBERG D12155-10 user manual Alert Tones & Volume, Restore Audio Defaults

Page 64

Advanced use

TANDBERG Videoconferencing System

The echo canceller tries to estimate the echo path from the speaker system to the microphones. Moving objects change this path, therefore try to avoid moving objects. Be especially aware of large objects and objects placed close to either the microphone or the speaker system as these objects will cause severe changes to the echo path.

Avoid putting paper sheets etc. on the microphone.

Avoid moving the microphone or loudspeaker.

In the event of poor echo cancelling, allow the canceller to adapt. After each change, the echo canceller requires a few seconds to adapt. Do not change the settings without allowing the echo canceller to adapt to the new audio environment.

In the presence of low frequency noise, enable the noise reduction (NR).

Alert Tones & Volume

To help distinguish between incoming video calls and ordinary telephone calls, different ringing tones may be selected. You may also select different volume levels for the ringing tone.

Alert Speaker

The system also has an internal, call alerting speaker.

On: The internal speaker will warn you of an incoming call even though the monitor may not be switched on.

Key Tones

The Key Tones may be switched on and off.

Restore Audio Defaults

There are many audio settings and the codec could easily be made unusable by configuring these by mistake. It is therefore possible to return all audio settings to their factory default settings by using Restore Audio Defaults.

64

Image 64
Contents UserManual Tandberg Videoconferencing System Environmental Issues Trademarks and copyrightOperator Safety Summary Contents Peripheral Equipment Advanced useAppendices 104 Index 114 Introduction TIPMenu structure LANTandberg 2500 Videoconferencing System At a glance the Tandberg 2500 systemMonitors V.E. II CameraCodec Remote control CabinetTable microphone Precautions InstallationUnpacking Page Connecting cables Power cableMonitor cables Microphone cableMonitor configuration 5a. Isdn cables using BRI interface5b. Other networks using the External Network interface LAN cableSystem configuration MenuIsdn configuration LAN configuration System start-up Getting startedWelcome menu Basics Making and ending calls Making a callTIP Selecting / setting default quality bandwidth Selecting / setting default network End a call Answer a callCorrecting keying mistakes Directory Press D Irectory to bring up the following menuEdit Entry Add New EntryDelete Entry Add MultiSite Entry Add SiteAdjusting volume General useView outgoing video selfview Microphone on/offDo Not Disturb / Sleep Mode On Screen SymbolsFocusing camera Controlling the Main CameraSelecting video sources Moving / zooming cameraVoice Activated Camera Positioning Selecting presets PresetsStoring presets Far end camera control Fecc Sending and receiving snapshots Sending a snapshotViewing a snapshot Receiving a snapshotDuo Video Add Duo VideoEnd a Duo Video call MultiSite MCU Establishing MultiSite meetings using Directory MultiSite cascadingAdding an extra site dial out Disconnecting sites from a conference Adding an extra site dialPC Presenter PC SoftPresenterWeb-interface Text Chat / Closed CaptioningStreaming Other PC applicationsSnapshots Advanced use Menu PasswordMain menu Call quality Advanced call quality QcifPresentation Mode Duo Video ModePresentations Duo Video QualityDuo Video Number Duo Video / Snapshot SourceAuto-Display Snapshot Snapshot FilterUtilities AutoanswerFar end camera control Dual MonitorAuto-PIP Welcome MenuContinuous Presence MCU status lineWeb Snapshots MCU services Quick Menu Request floor Release floorTerminal Names View site #Chair control Audio Settings Audio InputsPage Level Settings Out1 +13.5dB Out2AUX Out3VCR Previous Menu Audio OutputsEcho Control Page Automatic Gain Control AGC Settings Alert Tones & Volume Restore Audio DefaultsCamera Tracking Mode Video SettingsDocument Camera Focus BrightnessWhitebalance Video NameVGA Settings VNC Settings Terminal Settings Network ConfigurationISDN-BRI Settings Spids This Service has Limited Access on Some Isdn Networks Parallel dial External network settings 35/RS-366 cable LAN Settings Page Settings Page Advanced H.323 Settings RsvpIP Precedence QoS TypeDiffserv IP Settings Snmp Settings Call Settings Access CodeIncoming MCU calls Incoming telephone callsEncryption Mode Encryption Secure ConferenceMax Call Length Network ProfilesDataport configuration Page Language Software OptionsSystem info DiagnosticsChannel status TIP Restore defaults Call statusTest subsystem View current settingsIP Address Conflict Check Peripheral Equipment InterfacesE2 only Dual Monitor XGA monitorDocument camera Multiple controllable cameras AudioScience microphone TrackerVCR Playback Video Cassette Recorder VCRVCR Recording Telephone Add-On Extra fixed camerasPC applications Additional microphones Appendices TandbergAppendix 2 Connecting the system to the Switched 56 network Using Telesync TS-256 SW56/ISDN adapterLoudspeaker volume Appendix 3 Environmental considerationsIris control and lighting BackgroundGuidelines for setting up videoconferencing rooms How to prepare a typical room for videoconferencingAppendix 4 Using the file system Custom logos · Go to the folder where your logo is located Appendix 6 Security ABC111 112 Appendix 6 Declaration of Conformity Index FeccTandberg Videoconferencing System Index Current settings 93 outgoing video 30 Viewing a still image