Texas Instruments manual Hardware Installation, USB-IF, MSP-FET430UIF, Flashing the LED

Page 16

Get Started Now!

1.6Hardware Installation, MSP-FET430Pxx0 (‘P120, ‘P140, ‘P410, ‘P430, ‘P440)

1)Use the 25-conductor cable to connect the FET Interface module to the parallel port of your PC.

2)Use the 14-conductor cable to connect the FET Interface module to the supplied Target Socket module.

3)Ensure that the MSP430 device is securely seated in the socket, and that its pin 1 (indicated with a circular indentation on the top surface) aligns with the “1” mark on the PCB.

4)Ensure that the two jumpers (LED and Vcc) near the 2x7 pin male connector are in place. Pictorials of the Target Socket module and its parts are presented in Appendix B.

1.7Hardware Installation, USB-IF, MSP-FET430UIF

Use the USB cable to connect the USB-FET Interface module to a USB port of your PC. The USB FET should be recognized instantly as the USB device driver should have been installed already with the Kickstart SW. If for any reason the Install Wizard starts, respond to the prompts and point the wizard to the driver files which are located in directory: <Installation Root>\Embedded Workbench x.x\430\bin\WinXP. Detailed driver installation instructions can be found in Appendix F.

After connecting to a PC the USB FET performs a selftest where the red LED flashes for about 2 seconds. If the selftest passed successfully, the green LED lits permanently.

Use the 14-conductor cable to connect the USB-FET Interface module to a target board, such as an MSP430-FETPxxx Target Socket Module.

Ensure that the MSP430 device is securely seated in the socket, and that its pin 1 (indicated with a circular indentation on the top surface) aligns with the “1” mark on the PCB.

Ensure that the two jumpers (LED and Vcc) near the 2x7 pin male connector are in place. Pictorials of the MSP430 Target Socket modules and their parts are presented in Appendix B.

The USB FET has additional features like: programming of the security fuse and adjustable target Vcc (1.8V–5.0V); target can be supplied with up to 100mA.

1.8 “Flash”ing the LED

This section demonstrates on the FET the equivalent of the C-language “Hello world!” introductory program; an application that flashes the LED is developed and downloaded to the FET, and then run.

1)Start the Workbench (START->PROGRAMS->IAR SYSTEMS->IAR

EMBEDDED WORKBENCH KICKSTART FOR MSP430 V3->IAR EMBEDDED WORKBENCH).

2)Use FILE->OPEN WORKSPACE to open the file at: <Installation Root>\Embedded Workbench x.x\430\FET_examples\fet_projects.eww. The workspace window will open.

1-4

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Users Guide 2004Important Notice Page July Read This First How to Use This ManualAbout This Manual Information About Cautions and Warnings Related Documentation From Texas InstrumentsIf You Need Assistance FCC WarningPage Contents Frequently Asked Questions Figures TablesPage Get Started Now TopicKit Contents, MSP-FET430X110 Software Installation Kit Contents, MSP-FET430UIFHardware Installation, MSP-FET430X110 Hardware Installation, USB-IF, MSP-FET430UIF Flashing the LEDGet Started Now Important MSP430 Documents on the CD-ROM and WEB Development Flow Using Kickstart OverviewProject Settings OUTPUT-OUTPUT FILE-EXECUTABLEFactory Settings Creating a Project from Scratch Using an Existing IAR V1.x/V2.x Project Stack Management within the .xcl FilesHow to Generate Texas Instrument .TXT and other format Files Overview of Example ProgramsDevelopment Flow Using Breakpoints Using C-SPYBreakpoint Types Using Single Step Using Watch Windows Page Design Considerations for In-Circuit Programming Bootstrap Loader External PowerDesign Considerations for In-Circuit Programming Device Signals PRGS430Design Considerations for In-Circuit Programming Signal connections for MSP-FET430X110 Design Considerations for In-Circuit Programming Jtag Signal Connections Frequently Asked Questions Hardware Program Development Assembler, C-Compiler, Linker Should Done or Not Return Omit Debugging C-SPY OPTIONS-FET DEBUGGER-CONNECTIONSFrequently Asked Questions Figure A-1. Modification to FET Interface module Frequently Asked Questions Frequently Asked Questions Frequently Asked Questions Frequently Asked Questions Frequently Asked Questions Figure B-1. MSP-FET430X110, Schematic HardwareFigure B-1. MSP-FET430X110, Schematic Figure B-2. MSP-FET430X110, PCB Pictorials Figure B-3. MSP-FET430IF FET Interface module, Schematic Figure B-4. MSP-FET430IF FET Interface module, PCB Pictorial Figure B-5. MSP-TS430DW28 Target Socket module, Schematic LED connected to P1.0 Hardware Jumper J7 Jumper J6Open to measure current Hardware Jumper J6 Open to disconnect LED History of changes to MSP-TS430PM64 Target Socket module Figure B-11. MSP-TSPN80 Target Socket module, Schematic Figure B-12. MSP-TSPN80 Target Socket module, PCB Pictorials Figure B-13. MSP-TSPZ100 Target Socket module, Schematic Jumper J6 Figure B-15. MSP-FET430UIF USB Interface schematics Hardware Hardware Hardware Hardware Page FET Specific Menus Emulator EMULATOR-POWER on Reset EMULATOR-GIE on/off EMULATOR-FORCE Single SteppingPin MSP430F44x and MSP430F43x Device Emulation Table D-1. F4xx/80-pin Signal Mapping P1.5/TACLK/ACLK P1.4/TBCLK/SMCLK P1.3/TBOUTH/SVSOUT Page TI to IAR 2.x/3.x Assembler Migration Segment Control Translating Asm430 Assembler Directives to A430 DirectivesIntroduction Character stringsSection Control Directives Description Asm430 Directive TI A430 Directive IARConstant Initialization Directives Listing Control DirectivesConditional-Assembly Directives File Reference DirectivesSymbol Control Directives ReptcMiscellaneous Directives Macro DirectivesPreprocessor Directives Additional A430 Directives IAR Asm430 directive A430 directiveLstpag + #if, #else, #elif Page MSP-FET430UIF Installation Guide Hardware Installation Figure F-1. WinXP Hardware RecognitionFigure F-3. WinXP Driver Location Selection Folder Figure F-4. WinXP Driver Installation Figure F-5. Device Manager
Top Page Image Contents