Seiko Group TM-L60 manual DIP-Switch Functions DIP-switch Functions, Baud Rate Selection

Page 19

nDIP-Switch Functions

Table 3-2. DIP-switch Functions

DIP SW

ON

OFF


	SW-1	Ignores data reception errors	Prints “?” for data reception errors
	SW-2	Data buffer 45 bytes	Data buffer 4 Kbytes

	SW-3	XON/XOFF control	DSR/DTR	control

	SW-4	With parity	without	parity

	SW-5	Even parity	Odd parity
	SW-6	Change baud rate (Refer to Table 3-3)

	SW-7
	SW-7
	SW-8	Change print density (Refer to Table 34)

	SW-9
	SW-9

	SW-10	Thermal label paper	Thermal paper

Table 3-3. Baud Rate Selection

Baud Rate	SW 1-6	SW 1-7

1200 bps	ON	ON
4800	OFF	O N

9600	ON	OFF

19200	OFF	OFF

Table 3-4. Print Density Selection

Print Density	SW 1-8	SW 1-9	Level

LIGHT	ON	ON	1
I	OFF	OFF	2
I
I	ON	OFF	3
I	ON	OFF	3

			4
DARK	OFF	ON	4

13

Image 19

Contents L 6 Page CC Class a FCC Compliance Statement for American Users Introduction Contents Appendix a General Specifications Setting UP Unpacking the Printer 1Checking the Contents of the BoxRemoving the Protective Material Choosing a Place for the PrinterPart names 4Names and Functions of PartsPaper red Power greenError red Operation panelPlugging in AC adapter Connecting the Power Supply to the PrinterConnecting the interface cable Connecting the Host Computer to the PrinterInstalling the roll paper Installing the Roll PaperPaper Slot How to adjust the paper-end detector Adjusting the Paper-end DetectorPaper-end detector Page Locating the DIP switches Setting the DIP SwitchesSetting the DIP switches Baud Rate Selection DIP-Switch Functions DIP-switch FunctionsPrint Density Selection 1Checking Operation with the Self Test II. Reference Switches Power switch 1Panel Switches and CommandsPaper-feed switch Printable area Printable Area and Label Paper ConditionsLabel paper Miscellaneous Notes Page Error LED red Error CorrectionBe inspected Error DisplayON/OFF Timing Pattern Recovery Command Standby State DisplayCleaning the head Cleaning the HeadRemoving Jammed Paper Cover-open DetectorCover-open detector How to use this table Controlling the printer with commandsCommands Command DescriptionsCommand descriptions XXX Command ESC ! n ESC SP nESC $ n1 n2 ESC & s n m ap s Xam-n+l ESC % n= n 1 + 2 5 6 X n 2 m = 0 ESC * m n1 n2 d kVertical Direction Horizontal Direction ESC = n ESC 3 nESC D nkNUL ESC @Range ESC E nESC J n ESC G nESC V n ESC R nESC n ESC ¥ n1 n2ESC a n Position ESC c 4 nESC c 5 n ESC p m n1 n2ESC d n ESC u n ESC t nESC Journal near-end GS*n1n2dn1xn2x8 GS FFDot Density GS/mGS a m n GS C 0 m n PER Feed switch or turning the power onGS Cl, GS C2, GS c, GS C GS C1 n1 n2 n3 n4 n5 n6T h c o u n t d o w n GS C2 n1 n2To stop counting GSC N1 N2 N3 N4 N5With counting down GS H nWith counting up GS f nGS k n d k NUL GS w nGS n1 n2 n3 Before printing How to write program Printing on the roll paperProgram Descriptions IntroductionSend Print Data GS H n Initialize printer again Printing bar codesRS-232C must be closed using this command Sample Program onto thermal paper Printing on label paper Sample Program onto thermal label paper Printing specifications Appendix a General SpecificationsCharacters specifications Paper Thermal paper Near-end detectorThermal label paper Reliability Electrical characteristicsEMI by using Epson PS-130 External dimensions and weightAppendix B Connectors Signal Name Sender Appendix C Interfaces Specifications RS-232C compatibleSerial interface timing Pin Number Signal Name Signal Direction FunctionPage Page International character set Command Name Appendix E Command SummaryGS C2 GS C