Seiko Group TM-L60 manual CC Class a FCC Compliance Statement for American Users

Page 3

CC CLASS A

FCC COMPLIANCE STATEMENT FOR AMERICAN USERS

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

The connection of a non-shielded printer interface cable to this printer will invalidate the FCC Verification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

FOR CANADIAN USERS

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the radio interference regula- tions of the Canadian Department of Communications.

Le present appareil numérique n’émet pas de bruits radioélectriques de- passant les limites applicables aux appareils numériques de Class A pre- scrites dans le règlement sur le brouillage radioélectrique édicté par le Min- stère des Communications du Canada.

Image 3

Contents L 6 Page CC Class a FCC Compliance Statement for American Users Introduction Contents Appendix a General Specifications Setting UP Unpacking the Printer 1Checking the Contents of the BoxRemoving the Protective Material Choosing a Place for the PrinterPart names 4Names and Functions of PartsPaper red Power greenError red Operation panelPlugging in AC adapter Connecting the Power Supply to the PrinterConnecting the interface cable Connecting the Host Computer to the PrinterInstalling the roll paper Installing the Roll PaperPaper Slot Adjusting the Paper-end Detector How to adjust the paper-end detectorPaper-end detector Page Setting the DIP Switches Locating the DIP switchesSetting the DIP switches DIP-Switch Functions DIP-switch Functions Baud Rate SelectionPrint Density Selection 1Checking Operation with the Self Test II. Reference 1Panel Switches and Commands Switches Power switchPaper-feed switch Printable Area and Label Paper Conditions Printable areaLabel paper Miscellaneous Notes Page Error LED red Error CorrectionBe inspected Error DisplayON/OFF Timing Pattern Recovery Command Standby State DisplayCleaning the head Cleaning the HeadCover-open Detector Removing Jammed PaperCover-open detector How to use this table Controlling the printer with commandsCommand Descriptions CommandsCommand descriptions XXX Command ESC ! n ESC SP nESC $ n1 n2 ESC & s n m ap s Xam-n+l ESC % n= n 1 + 2 5 6 X n 2 m = 0 ESC * m n1 n2 d kVertical Direction Horizontal Direction ESC = n ESC 3 nESC D nkNUL ESC @Range ESC E nESC J n ESC G nESC V n ESC R nESC ¥ n1 n2 ESC nESC a n Position ESC c 4 nESC p m n1 n2 ESC c 5 nESC d n ESC u n ESC t nESC Journal near-end GS*n1n2dn1xn2x8 GS FFDot Density GS/mGS a m n GS C 0 m n PER Feed switch or turning the power onGS Cl, GS C2, GS c, GS C GS C1 n1 n2 n3 n4 n5 n6T h c o u n t d o w n GS C2 n1 n2To stop counting GSC N1 N2 N3 N4 N5With counting down GS H nWith counting up GS f nGS k n d k NUL GS w nGS n1 n2 n3 Before printing How to write program Printing on the roll paperProgram Descriptions IntroductionSend Print Data GS H n Initialize printer again Printing bar codesRS-232C must be closed using this command Sample Program onto thermal paper Printing on label paper Sample Program onto thermal label paper Appendix a General Specifications Printing specificationsCharacters specifications Paper Thermal paper Near-end detectorThermal label paper Reliability Electrical characteristicsEMI by using Epson PS-130 External dimensions and weightAppendix B Connectors Signal Name Sender Appendix C Interfaces Specifications RS-232C compatibleSerial interface timing Pin Number Signal Name Signal Direction FunctionPage Page International character set Command Name Appendix E Command SummaryGS C2 GS C