Seiko Group TM-L60 manual Appendix a General Specifications, Printing specifications

Page 67

		APPENDIX

	APPENDIX A General Specifications

	1. Printing specifications
	Printing method:	Thermal line printing
	Dot density:	180 dpi
	Printing direction:	Uni-directional with friction feed
		When the GS FF command is executed printing
		is performed in the reverse direction.
	Print width:	54 mm, 384-dot positions
	Characters per line:	Normal paper:	32 (Font A)
		42 (Font B)
		Label paper:	30 (Font A)
		40 (Font B)
	Character spacing:	0.28 mm (Font A)
		0.28 mm (Font B)
		Programmable by control command.
	Printing speed:	Approx. 12 lines/second (1/6 inch feed) (* 1)
		Approx. 18 lines/second (1/9 inch feed) (* 1)
		Approx. 2.0 inches/second (* 1)
		Printing speed may slow down depending on the
		data transmission speed and combination of con-
		trol commands.
	Paper feeding speed:	Approx. 2.0 inches/second (* 1)
		(Approx. 50.0 mm/second)
	Line spacing:	1/6 inch (4.23 mm) default
		Programmable by control command.
		(Minimum 1/360 inch)

(* 1): These speed values indicate approximate printing and paper feeding speeds between the beginning and ending of a given label.

2.Characters specifications

Character sets:	Alphanumeric:	95
	Enlarged graphics:	128 X 2 pages
	International:	32

61

Image 67

Contents L 6 Page CC Class a FCC Compliance Statement for American Users Introduction Contents Appendix a General Specifications Setting UP Unpacking the Printer 1Checking the Contents of the BoxRemoving the Protective Material Choosing a Place for the PrinterPart names 4Names and Functions of PartsPaper red Power greenError red Operation panelPlugging in AC adapter Connecting the Power Supply to the PrinterConnecting the interface cable Connecting the Host Computer to the PrinterInstalling the roll paper Installing the Roll PaperPaper Slot How to adjust the paper-end detector Adjusting the Paper-end DetectorPaper-end detector Page Locating the DIP switches Setting the DIP SwitchesSetting the DIP switches Baud Rate Selection DIP-Switch Functions DIP-switch FunctionsPrint Density Selection 1Checking Operation with the Self Test II. Reference Switches Power switch 1Panel Switches and CommandsPaper-feed switch Printable area Printable Area and Label Paper ConditionsLabel paper Miscellaneous Notes Page Error LED red Error CorrectionBe inspected Error DisplayON/OFF Timing Pattern Recovery Command Standby State DisplayCleaning the head Cleaning the HeadRemoving Jammed Paper Cover-open DetectorCover-open detector How to use this table Controlling the printer with commandsCommands Command DescriptionsCommand descriptions XXX Command ESC ! n ESC SP nESC $ n1 n2 ESC & s n m ap s Xam-n+l ESC % n= n 1 + 2 5 6 X n 2 m = 0 ESC * m n1 n2 d kVertical Direction Horizontal Direction ESC = n ESC 3 nESC D nkNUL ESC @Range ESC E nESC J n ESC G nESC V n ESC R nESC n ESC ¥ n1 n2ESC a n Position ESC c 4 nESC c 5 n ESC p m n1 n2ESC d n ESC u n ESC t nESC Journal near-end GS*n1n2dn1xn2x8 GS FFDot Density GS/mGS a m n GS C 0 m n PER Feed switch or turning the power onGS Cl, GS C2, GS c, GS C GS C1 n1 n2 n3 n4 n5 n6T h c o u n t d o w n GS C2 n1 n2To stop counting GSC N1 N2 N3 N4 N5With counting down GS H nWith counting up GS f nGS k n d k NUL GS w nGS n1 n2 n3 Before printing How to write program Printing on the roll paperProgram Descriptions IntroductionSend Print Data GS H n Initialize printer again Printing bar codesRS-232C must be closed using this command Sample Program onto thermal paper Printing on label paper Sample Program onto thermal label paper Printing specifications Appendix a General SpecificationsCharacters specifications Paper Thermal paper Near-end detectorThermal label paper Reliability Electrical characteristicsEMI by using Epson PS-130 External dimensions and weightAppendix B Connectors Signal Name Sender Appendix C Interfaces Specifications RS-232C compatibleSerial interface timing Pin Number Signal Name Signal Direction FunctionPage Page International character set Command Name Appendix E Command SummaryGS C2 GS C