Seiko Group TM-L60 manual Esc

Page 47

[Notes]

ESC v

•The transmitted status is only one byte and the data is as shown in the following table.

•If nothing is connected with Drawer kick-out connector, bit 0 of n is always “1".

•When DTR/DSR control is selected, one byte is transmitted af- ter confirming that the host computer is ready to receive data (DSR is SPACE).

•When XON/XOFF control is selected, one byte is transmitted without checking the DSR signal.

•When DTR/DSR control is selected, if the host computer is not ready to receive data (DSR is MARK), the printer waits until it becomes ready.

		V a l u e
B i t	Function
B i t	Function	0	1

0	Pin 3 level	"LOW"	"HIGH"

1	Undefined

2	Undefined

3	Undefined

4	Unused	Fixed to 0
4	Unused	Fixed to 0

5	Undefined

6	Undefined

7	Undefined

[Name]	Transmit printer status
[Format]	<1B>H<76>H
[Description]	The current printer status is transmitted to the host computer.
[Notes]	• The transmitted status is only one byte and the data is as shown
	in the following table.
	• When DTR/DSR control is selected, one byte is transmitted af-
	ter confirming that the host computer is ready to receive data
	(DSR is SPACE).
	• When XON/XOFF control is selected, one byte is transmitted
	without checking the DSR signal.
	• When DTR/DSR control is selected, if the host computer is not
	ready to receive data (DSR is MARK), the printer waits until it
	becomes ready.

41

Image 47

Contents L 6 Page CC Class a FCC Compliance Statement for American Users Introduction Contents Appendix a General Specifications Setting UP Unpacking the Printer 1Checking the Contents of the BoxRemoving the Protective Material Choosing a Place for the PrinterPart names 4Names and Functions of PartsPaper red Power greenError red Operation panelPlugging in AC adapter Connecting the Power Supply to the PrinterConnecting the interface cable Connecting the Host Computer to the PrinterInstalling the roll paper Installing the Roll PaperPaper Slot Paper-end detector Adjusting the Paper-end DetectorHow to adjust the paper-end detector Page Setting the DIP switches Setting the DIP SwitchesLocating the DIP switches Print Density Selection DIP-Switch Functions DIP-switch FunctionsBaud Rate Selection 1Checking Operation with the Self Test II. Reference Paper-feed switch 1Panel Switches and CommandsSwitches Power switch Label paper Printable Area and Label Paper ConditionsPrintable area Miscellaneous Notes Page Error LED red Error CorrectionBe inspected Error DisplayON/OFF Timing Pattern Recovery Command Standby State DisplayCleaning the head Cleaning the HeadCover-open detector Cover-open DetectorRemoving Jammed Paper How to use this table Controlling the printer with commandsCommand descriptions XXX Command Command DescriptionsCommands ESC ! n ESC SP nESC $ n1 n2 ESC & s n m ap s Xam-n+l ESC % n= n 1 + 2 5 6 X n 2 m = 0 ESC * m n1 n2 d kVertical Direction Horizontal Direction ESC = n ESC 3 nESC D nkNUL ESC @Range ESC E nESC J n ESC G nESC V n ESC R nESC a n ESC ¥ n1 n2ESC n Position ESC c 4 nESC d n ESC p m n1 n2ESC c 5 n ESC u n ESC t nESC Journal near-end GS*n1n2dn1xn2x8 GS FFDot Density GS/mGS a m n GS C 0 m n PER Feed switch or turning the power onGS Cl, GS C2, GS c, GS C GS C1 n1 n2 n3 n4 n5 n6T h c o u n t d o w n GS C2 n1 n2To stop counting GSC N1 N2 N3 N4 N5With counting down GS H nWith counting up GS f nGS k n d k NUL GS w nGS n1 n2 n3 Before printing How to write program Printing on the roll paperProgram Descriptions IntroductionSend Print Data GS H n Initialize printer again Printing bar codesRS-232C must be closed using this command Sample Program onto thermal paper Printing on label paper Sample Program onto thermal label paper Characters specifications Appendix a General SpecificationsPrinting specifications Paper Thermal paper Near-end detectorThermal label paper Reliability Electrical characteristicsEMI by using Epson PS-130 External dimensions and weightAppendix B Connectors Signal Name Sender Appendix C Interfaces Specifications RS-232C compatibleSerial interface timing Pin Number Signal Name Signal Direction FunctionPage Page International character set Command Name Appendix E Command SummaryGS C2 GS C