Seiko Group TM-L60 manual Appendix C Interfaces, Specifications RS-232C compatible

Page 73

n1 x 2 ms

n2 x 2 ms

Figure B-1. Drawer Kick-out Drive Signal

Printer side

User side

Figure B-2. Drawer Kick-out Signal Interface Circuit

NOTES: • The circuit on the user side should be designed so that the drawer drive duty is as shown below.

ON time

≤0.2

ON time + OFF time

•The waveform shown in Figure B-l is output at Point A in Figure B-2 (n1 (ON time) and n2 (OFF time) depend on the ESC p command.)

APPENDIX C Interfaces

1. Specifications (RS-232C compatible)
Data transmission:	Serial
Synchronization:	Asynchronous
Handshaking:	DTR/DSR or XON/XOFF control
Signal level:	MARK = -3 to -15 V:	Logic “1”
	SPACE = +3 to + 15 V:	Logic “0”
Baud rates:	1200,4800,9600,19200 bps
Bit length:	8 bits
Parity:	Invalid, even, odd
Stop bits:	1 bit or more
Connector:	D-SUB 25 pin connector

67

Image 73

Contents L 6 Page CC Class a FCC Compliance Statement for American Users Introduction Contents Appendix a General Specifications Setting UP Unpacking the Printer 1Checking the Contents of the BoxRemoving the Protective Material Choosing a Place for the PrinterPart names 4Names and Functions of PartsError red Power greenOperation panel Paper redPlugging in AC adapter Connecting the Power Supply to the PrinterConnecting the interface cable Connecting the Host Computer to the PrinterInstalling the roll paper Installing the Roll PaperPaper Slot How to adjust the paper-end detector Adjusting the Paper-end DetectorPaper-end detector Page Locating the DIP switches Setting the DIP SwitchesSetting the DIP switches Baud Rate Selection DIP-Switch Functions DIP-switch FunctionsPrint Density Selection 1Checking Operation with the Self Test II. Reference Switches Power switch 1Panel Switches and CommandsPaper-feed switch Printable area Printable Area and Label Paper ConditionsLabel paper Miscellaneous Notes Page Error LED red Error CorrectionBe inspected Error DisplayON/OFF Timing Pattern Recovery Command Standby State DisplayCleaning the head Cleaning the HeadRemoving Jammed Paper Cover-open DetectorCover-open detector How to use this table Controlling the printer with commandsCommands Command DescriptionsCommand descriptions XXX Command ESC ! n ESC SP nESC $ n1 n2 ESC & s n m ap s Xam-n+l ESC % n= n 1 + 2 5 6 X n 2 m = 0 ESC * m n1 n2 d kVertical Direction Horizontal Direction ESC = n ESC 3 nESC D nkNUL ESC @Range ESC E nESC J n ESC G nESC V n ESC R nESC n ESC ¥ n1 n2ESC a n Position ESC c 4 nESC c 5 n ESC p m n1 n2ESC d n ESC u n ESC t nESC Journal near-end GS*n1n2dn1xn2x8 GS FFDot Density GS/mGS a m n GS C 0 m n PER Feed switch or turning the power onGS Cl, GS C2, GS c, GS C GS C1 n1 n2 n3 n4 n5 n6T h c o u n t d o w n GS C2 n1 n2To stop counting GSC N1 N2 N3 N4 N5With counting down GS H nWith counting up GS f nGS k n d k NUL GS w nGS n1 n2 n3 Program Descriptions How to write program Printing on the roll paperIntroduction Before printingSend Print Data GS H n Initialize printer again Printing bar codesRS-232C must be closed using this command Sample Program onto thermal paper Printing on label paper Sample Program onto thermal label paper Printing specifications Appendix a General SpecificationsCharacters specifications Paper Thermal paper Near-end detectorThermal label paper EMI by using Epson PS-130 Electrical characteristicsExternal dimensions and weight ReliabilityAppendix B Connectors Signal Name Sender Appendix C Interfaces Specifications RS-232C compatibleSerial interface timing Pin Number Signal Name Signal Direction FunctionPage Page International character set Command Name Appendix E Command SummaryGS C2 GS C