Seiko Group TM-L60 manual Installing the Roll Paper, Installing the roll paper

Page 14

Chapter 3 Installing the Parts

3-1 Installing the Roll Paper

nInstalling the roll paper

Be sure to use roll paper that matches the printer’s specifications.

Using scissors, cut the leading edge of the roll paper perpendicular to the paper feed direction.

Open the roll-paper cover and raise the release lever toward you.

Make sure to pull the release lever out until the paper slot of the printer mechanism will be faced up.

Paper Slot

Load the roll paper while lightly pressing the right roll paper holder outward. Release the holder after fitting the paper core onto the holder. Make sure the

roll paper turns freely.

•When loading roll paper, make sure to insert so that it rotates in the correct direction.

Correct

Incorrect

8

Image 14

Contents L 6 Page CC Class a FCC Compliance Statement for American Users Introduction Contents Appendix a General Specifications Setting UP 1Checking the Contents of the Box Unpacking the PrinterChoosing a Place for the Printer Removing the Protective Material4Names and Functions of Parts Part namesOperation panel Power greenError red Paper redConnecting the Power Supply to the Printer Plugging in AC adapterConnecting the Host Computer to the Printer Connecting the interface cableInstalling the Roll Paper Installing the roll paperPaper Slot Paper-end detector Adjusting the Paper-end DetectorHow to adjust the paper-end detector Page Setting the DIP switches Setting the DIP SwitchesLocating the DIP switches Print Density Selection DIP-Switch Functions DIP-switch FunctionsBaud Rate Selection 1Checking Operation with the Self Test II. Reference Paper-feed switch 1Panel Switches and CommandsSwitches Power switch Label paper Printable Area and Label Paper ConditionsPrintable area Miscellaneous Notes Page Error Correction Error LED redError Display Be inspectedCommand Standby State Display ON/OFF Timing Pattern RecoveryCleaning the Head Cleaning the headCover-open detector Cover-open DetectorRemoving Jammed Paper Controlling the printer with commands How to use this tableCommand descriptions XXX Command Command DescriptionsCommands ESC SP n ESC ! nESC $ n1 n2 ESC % n ESC & s n m ap s Xam-n+lESC * m n1 n2 d k = n 1 + 2 5 6 X n 2 m = 0Vertical Direction Horizontal Direction ESC 3 n ESC = nESC @ ESC D nkNULESC E n RangeESC G n ESC J nESC R n ESC V nESC a n ESC ¥ n1 n2ESC n ESC c 4 n PositionESC d n ESC p m n1 n2ESC c 5 n ESC t n ESC u nESC Journal near-end GS FF GS*n1n2dn1xn2x8GS/m Dot DensityGS a m n PER Feed switch or turning the power on GS C 0 m nGS C1 n1 n2 n3 n4 n5 n6 GS Cl, GS C2, GS c, GS CGS C2 n1 n2 T h c o u n t d o w nGSC N1 N2 N3 N4 N5 To stop countingGS H n With counting downGS f n With counting upGS w n GS k n d k NULGS n1 n2 n3 Introduction How to write program Printing on the roll paperProgram Descriptions Before printingSend Print Data Initialize printer again Printing bar codes GS H nRS-232C must be closed using this command Sample Program onto thermal paper Printing on label paper Sample Program onto thermal label paper Characters specifications Appendix a General SpecificationsPrinting specifications Near-end detector Paper Thermal paperThermal label paper External dimensions and weight Electrical characteristicsEMI by using Epson PS-130 ReliabilityAppendix B Connectors Signal Name Sender Specifications RS-232C compatible Appendix C InterfacesPin Number Signal Name Signal Direction Function Serial interface timingPage Page International character set Appendix E Command Summary Command NameGS C GS C2