Sharp XV-Z30000 appendix Introduction

Page 17

Numbers in Z refer to the main pages in this operation manual where the topic is explained.

Introduction

1

2

3

4

 

5

15

6

 

7 16

8 17

9 18

10

19

11

20

12

21

13

 

14

22

1ON button 28

For turning the power on.

2STANDBY button 28

For putting the projector into the Standby mode.

3CONTRAST, BRIGHTNESS, COLOR and TINT buttons 37

For adjusting the contrast, brightness, color and tint.

4HDMI 1/2, COMPONENT and COMPUTER buttons 35

For switching to the respective input modes.

5PICTURE MODE button 37

For displaying the Picture Mode list.

6RESIZE button 36

For switching the picture size (NORMAL, 16:9, etc.).

7ANAMORPHIC button

For switching the Anamorphic lens.

8Adjustment buttons (P/R/O/Q) 42 For selecting and adjusting menu items.

9RETURN button 42

For returning to the previous menu screen during menu operations.

10ZOOM buttons 30

For adjusting the projected image size.

11H&V SHIFT button 29

For shifting the lens horizontally and vertically.

12AUTO SYNC button 38

For automatically adjusting images when connected to a computer.

13MEMORY 1/2 buttons 56

For displaying each “Load Memory” screen of “Memory Menu”.

MEMORY button 56

For displaying the Memory Menu screen.

143D ON/OFF button 68, 69

For switching between 2D and 3D modes.

15IRIS 1/2 buttons 38

For adjusting the quantity of the projected light and the contrast of the image.

16MENU button 42

For displaying adjustment and setting screens.

17ENTER button 42

For setting items selected or adjusted on the menu.

18MENU HIDE button 38

For temporarily hiding menu screen.

19FOCUS buttons 30 For adjusting the focus.

20KEYSTONE button 31

For entering the Keystone Correction mode.

21ECO+QUIET button 38

For lowering the noise of the cooling fan and extending the lamp life.

223D MENU button 69, 70

For displaying the 3D MENU screen.

15

Image 17
Contents XV-Z30000 Model No Serial No Void the users authority to operate this equipment See bottom of projectorSharp Plaza, Mahwah, New Jersey TEL 1-800-BE-SHARP InformationFor Future Reference Using the Menu ScreenContents Reference Adjusting the Projector Function PRJ-ADJ MenuPower Sources CleaningAccessories Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingDo not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally Other connected equipment Using the projector in other countriesTemperature monitor function Observe the following safeguards when using the 3D Glasses For Macintosh When you want to view the Setup ManualFor Windows Optional accessories AccessoriesPart Names and Functions Power indicator Lamp indicator Temperature warning indicatorRear View Terminals Using the Kensington LockIntroduction Inserting the Batteries Ensure that you do not drop it or expose it to Remote control sensor 33 n 10 mUsable Range Easy Start Setup and ProjectionControl On the remote controlVideo Setup Setting Up the ProjectorSetting Up the Projector Standard Setup Front ProjectionFormula for picture size and projection distance Screen Size and Projection DistanceCeiling-Mount Setup Projection PRJ ModeTerminals on the Projector Connecting the Projector to Other EquipmentConnecting to Video Equipment Connecting to a computer using the RGB cable Connecting to a ComputerControlling the Projector by a Computer AC socket Power cord supplied To AC outlet Connecting the Power CordWhen connecting to the LAN terminal using a LAN cable Turning the Projector On Turning the Projector On/OffImage Projection Press H&V Shift on the remote controlShifting the Lens ROn-screen displayAdjusting the Focus Using the Adjustment FeetAdjusting the Projected Image Size Rotate the adjustment feet to adjust the projected anglePress Keystone Press P/R/O/Q to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Geometric Adjustment Press P or R to parallelize Press P/R to select H&V KEYSTONE, and then pressLeft and right sides Press Keystone to set the positionPress Keystone to set theAdjustment with R/O position Press P/R/O/Q to adjustPress P/R to select SPHERE, and then press Enter Sphere correctionHdmi 1/2, Component and Computer buttons Switching the Input ModeInput list Press Resize on the remote control or on the projector Resize ModeAdjusting the Image Operating with the Remote ControlSelecting the Picture Mode Press image adjustment buttonsAuto Sync Auto Sync Adjustment Switching the Iris SettingSwitching the Eco+Quiet Mode Hiding the Menu Temporarily Menu HidePicture menu Menu ItemsRGB 3D Menu Menu Selections Adjustments Using the Menu ScreenPress Q or O and select Picture to adjust Press MenuPress P or R and select Bright to adjust To adjust the projected image while watching itPress O or Q to adjust the item selected Press EnterMenu operation n Picture Adjustment Picture Menu Selecting the Picture Mode  Switching the Iris Setting Adjusting the ImageUsing the Advanced Eco+QuietAdjust the curve to adjust the image brightness  Adjusting the ColorsCustom Gamma PickerS. color adjustment screen Selecting the Film Mode Adjusting the Bright BoostSetting Detail Enhancement Resetting All Adjustment ItemsSetting the Resolution Computer Image Adjustment SIG-ADJ MenuSetting the Video Setup Signal Type SettingAdjusting the Dynamic Range Signal InfoSetting the Resize Mode Adjusting the Projected Image SCR-ADJ Menu2Adjusting the Image Position TriggerAdjusting the Overscan Adjusting the Projected Image SCR-ADJ Menu ContinueSetting On-screen Display Black MaskSelecting the Menu Screen Position See page 22 for details of Projection PRJ ModeReversing/Inverting Projected Images Selecting the On-screen Display LanguageEconomy Mode Setting No Operation Off ModeSetting the Power Save Mode Economy Mode Setting the One-Touch Playback Function One Touch Play Setting One Touch PlaySetting the System Standby Function System Standby Setting the Input Terminal Names Input Name Setting the Demo Mode Adjusting the Projector Function PRJ-ADJ Menu Fan Mode Setting Turning LED Off Lamp Timer Life Returning to the Default SettingsSetting a Password Setting Up the Projector Network Environment Network MenuSelect Password, then press Q On the projector, pressTCP/IP Setting Dhcp Client SettingReturning to Default Settings Network Enter IP Address using P, R, Q and O, then press EnterYou can confirm the following items Confirming the Projector InformationEnjoying 3D Image Viewing Precautions on using the 3D GlassesPrecautions on installing the IR emitter As you get more comfortable viewing 3D images Precautions on viewing 3D imagesEpilepsy Part Names Supplied Accessories for the 3D GlassesReplacing the Button Cell Battery Before Using the 3D GlassesRemove the button cell battery Close the battery coverAttaching the 3D Glasses Band Using the 3D GlassesAttaching the Nose Pad Install the IR emitter unit to the stand Connecting the IR Emitter to the ProjectorPosition the IR emitter To 3D Synchro terminal IR emitter cableWhen 3D Auto Change is set to Yes When 3D Auto Change is set to NoViewing 3D Images Turn on the 3D Glasses and place them over your eyesPress P/R to select 3D Press O/Q to select On or Off Press 3D Menu3D Auto Change 3D Depth Adjust3D Format Viewing Time InfoSetting the 3D Format Menu 3D Glasses lenses S 0 8 B Manufacture number Color Specifications 3D GlassesEffective Distance DimensionsCleaning the projector MaintenanceCleaning the lens or lens cover Cleaning the exhaust and intake ventsAbout the lamp indicator Maintenance IndicatorsAbout the temperature warning indicator Red on Abnormally high Are high Lower than 95F +35ºC Replacing the Lamp Regarding the LampLamp Disconnect the power cord Removing and Installing the Lamp UnitRemove the lamp unit cover Lamp unitResetting the Lamp Timer Computer Compatibility ChartDTV 23-27 TroubleshootingProblem Check 68-70 For Sharp Assistance Hdmi SpecificationsDimensions Index