Sharp XV-Z30000 appendix Custom Gamma,  Adjusting the Colors, Picker

Page 48

Picture Adjustment (“Picture” Menu) (Continued)

7 Custom Gamma

The Custom Gamma function can be used when “Picture Mode” is set to “User1” or “User2”.

You can adjust the gamma curve and save your custom setting. Adjust it to suit the picture brightness.

1Press P/R to select “Custom

Gamma” on the gamma

adjustment screen, and then press Q.

Custom Gamma

Custom Gamma

Off

Custom Gamma Edit

Reset

Return

SEL./ADJ.

ENTER

RETURN

END

2 Press P/R to select “On”.

3 Press R to select “Custom

Gamma Edit”, and then press

ENTER.

4Adjust the curve to adjust the image brightness.

Press O/Q to adjust the white level. Select from 10 levels, from 5% to 80%.

Press P/R to adjust the optical output value. Select a value from 0 to 100.

 

Custom Gamma

 

 

Custom Gamma

On

 

Custom Gamma Edit

 

 

Reset

 

 

Return

 

Output:

 

 

XX%

 

 

 

Input:

XX%

SEL./ADJ.

ENTER

RETURN

END

 

Menu operation n Page 42

5Press ENTER to display the confirmation screen. Use P/R to

select “Save” and press ENTER.

6 To complete the Custom Gamma adjustment, select “Return” and press ENTER.

Adjusting the Colors

You can select the color of the projected image to correct and then adjust it to the desired color by setting “Hue”, “Saturation”, “Value”, and “Effect”.

Note

Before performing this adjustment, prepare the image to be adjusted.

You can perform this adjustment easier in the still image than in the moving image.

1 Select “C.M.S.1” or “C.M.S.2” (C.M.S.: Color Management

System) in the “Advanced” menu, and press Q.

If there is no data for the stored corrected color, the color selection screen and the picker is displayed. (Go to step 2.)

Picker

46

Image 48
Contents XV-Z30000 Model No Serial No See bottom of projector Void the users authority to operate this equipmentInformation Sharp Plaza, Mahwah, New Jersey TEL 1-800-BE-SHARPUsing the Menu Screen For Future ReferenceContents Adjusting the Projector Function PRJ-ADJ Menu ReferenceCleaning Power SourcesAccessories Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Observe the following safeguards when using the 3D Glasses When you want to view the Setup Manual For WindowsFor Macintosh Accessories Optional accessoriesPower indicator Lamp indicator Temperature warning indicator Part Names and FunctionsUsing the Kensington Lock Rear View TerminalsIntroduction Inserting the Batteries Remote control sensor 33 n 10 m Usable RangeEnsure that you do not drop it or expose it to Setup and Projection Easy StartOn the remote control ControlSetting Up the Projector Video SetupSetting Up the Projector Standard Setup Front ProjectionScreen Size and Projection Distance Formula for picture size and projection distanceProjection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment Terminals on the ProjectorConnecting to Video Equipment Connecting to a Computer Connecting to a computer using the RGB cableControlling the Projector by a Computer Connecting the Power Cord When connecting to the LAN terminal using a LAN cableAC socket Power cord supplied To AC outlet Turning the Projector On/Off Turning the Projector OnPress H&V Shift on the remote control Image ProjectionShifting the Lens ROn-screen displayUsing the Adjustment Feet Adjusting the FocusAdjusting the Projected Image Size Rotate the adjustment feet to adjust the projected anglePress P/R/O/Q to adjust Keystone Correction Correcting Trapezoidal DistortionPress Keystone Geometric Adjustment Press P/R to select H&V KEYSTONE, and then press Press P or R to parallelizeLeft and right sides Press Keystone to set the positionPress P/R/O/Q to adjust Press Keystone to set theAdjustment with R/O positionPress P/R to select SPHERE, and then press Enter Sphere correctionSwitching the Input Mode Input listHdmi 1/2, Component and Computer buttons Resize Mode Press Resize on the remote control or on the projectorOperating with the Remote Control Adjusting the ImageSelecting the Picture Mode Press image adjustment buttonsSwitching the Iris Setting Auto Sync Auto Sync AdjustmentSwitching the Eco+Quiet Mode Hiding the Menu Temporarily Menu HideMenu Items Picture menuRGB 3D Menu Using the Menu Screen Menu Selections AdjustmentsPress Q or O and select Picture to adjust Press MenuTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press EnterPicture Adjustment Picture Menu  Selecting the Picture ModeMenu operation n Adjusting the Image  Switching the Iris SettingUsing the Advanced Eco+Quiet Adjusting the Colors Adjust the curve to adjust the image brightnessCustom Gamma PickerS. color adjustment screen Adjusting the Bright Boost Selecting the Film ModeSetting Detail Enhancement Resetting All Adjustment ItemsComputer Image Adjustment SIG-ADJ Menu Setting the ResolutionSignal Type Setting Setting the Video SetupAdjusting the Dynamic Range Signal InfoAdjusting the Projected Image SCR-ADJ Menu Setting the Resize Mode2Adjusting the Image Position TriggerAdjusting the Projected Image SCR-ADJ Menu Continue Adjusting the OverscanSetting On-screen Display Black MaskSee page 22 for details of Projection PRJ Mode Selecting the Menu Screen PositionReversing/Inverting Projected Images Selecting the On-screen Display LanguageSetting No Operation Off Mode Setting the Power Save Mode Economy ModeEconomy Mode Setting One Touch Play Setting the One-Touch Playback Function One Touch PlaySetting the System Standby Function System Standby Setting the Input Terminal Names Input NameAdjusting the Projector Function PRJ-ADJ Menu  Setting the Demo Mode Fan Mode Setting Turning LED OffReturning to the Default Settings  Lamp Timer LifeSetting Up the Projector Network Environment Network Menu Setting a PasswordSelect Password, then press Q On the projector, pressDhcp Client Setting TCP/IP SettingReturning to Default Settings Network Enter IP Address using P, R, Q and O, then press EnterConfirming the Projector Information You can confirm the following itemsPrecautions on using the 3D Glasses Precautions on installing the IR emitterEnjoying 3D Image Viewing Precautions on viewing 3D images As you get more comfortable viewing 3D imagesEpilepsy Supplied Accessories for the 3D Glasses Part NamesBefore Using the 3D Glasses Replacing the Button Cell BatteryRemove the button cell battery Close the battery coverUsing the 3D Glasses Attaching the Nose PadAttaching the 3D Glasses Band Connecting the IR Emitter to the Projector Install the IR emitter unit to the standPosition the IR emitter To 3D Synchro terminal IR emitter cableWhen 3D Auto Change is set to No When 3D Auto Change is set to YesViewing 3D Images Turn on the 3D Glasses and place them over your eyesPress 3D Menu Press P/R to select 3D Press O/Q to select On or Off3D Depth Adjust 3D Auto Change3D Format Viewing Time InfoSetting the 3D Format Menu 3D Glasses lenses Specifications 3D Glasses S 0 8 B Manufacture number ColorDimensions Effective DistanceMaintenance Cleaning the projectorCleaning the lens or lens cover Cleaning the exhaust and intake ventsMaintenance Indicators About the temperature warning indicatorAbout the lamp indicator Red on Abnormally high Are high Lower than 95F +35ºC Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Lamp unitResetting the Lamp Timer Compatibility Chart ComputerDTV Troubleshooting 23-27Problem Check 68-70 For Sharp Assistance Specifications HdmiDimensions Index