Sharp XV-Z30000 appendix Maintenance Indicators, About the temperature warning indicator

Page 78

Maintenance Indicators

■The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector.

■If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter Standby mode. After the projector has entered Standby mode, follow the procedures given below.

Top View Temperature warning indicator Lamp indicator

Power indicator

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising,

“” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter Standby mode. When you ﬁ nd the temperature warning indicator blinking, be sure to perform the measures described on page 77.

About the lamp indicator

■When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp.” will be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter Standby mode. At this time, the lamp indicator will illuminate in red.

■If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.

Indicators on the Projector

Power indicator	Red on	Normal (Standby)
	Green on	Normal (Power on)
	Red blinks	Abnormal (See page 77.)
	Green blinks	Normal (Cooling)
Lamp indicator	Green on	Normal
	Green blinks	The lamp is warming up.
	Red on	The lamp is shut down abnormally or requires to be
		changed. (See page 77.)
Temperature	Off	Normal
warning indicator	Red on/Red blinks	The internal temperature is abnormally high. (See page 77.)

76

Image 78

Contents XV-Z30000 Model No Serial No See bottom of projector Void the users authority to operate this equipmentInformation Sharp Plaza, Mahwah, New Jersey TEL 1-800-BE-SHARPUsing the Menu Screen For Future ReferenceContents Adjusting the Projector Function PRJ-ADJ Menu ReferenceAccessories CleaningPower Sources Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts OverloadingAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Observe the following safeguards when using the 3D Glasses When you want to view the Setup Manual For WindowsFor Macintosh Accessories Optional accessoriesPower indicator Lamp indicator Temperature warning indicator Part Names and FunctionsUsing the Kensington Lock Rear View TerminalsIntroduction Inserting the Batteries Remote control sensor 33 n 10 m Usable RangeEnsure that you do not drop it or expose it to Setup and Projection Easy StartOn the remote control ControlSetting Up the Projector Setting Up the ProjectorVideo Setup Standard Setup Front ProjectionScreen Size and Projection Distance Formula for picture size and projection distanceProjection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment Terminals on the ProjectorConnecting to Video Equipment Connecting to a Computer Connecting to a computer using the RGB cableControlling the Projector by a Computer Connecting the Power Cord When connecting to the LAN terminal using a LAN cableAC socket Power cord supplied To AC outlet Turning the Projector On/Off Turning the Projector OnShifting the Lens Press H&V Shift on the remote controlImage Projection ROn-screen displayAdjusting the Projected Image Size Using the Adjustment FeetAdjusting the Focus Rotate the adjustment feet to adjust the projected anglePress P/R/O/Q to adjust Keystone Correction Correcting Trapezoidal DistortionPress Keystone Geometric Adjustment Left and right sides Press P/R to select H&V KEYSTONE, and then pressPress P or R to parallelize Press Keystone to set the positionPress P/R to select SPHERE, and then press Enter Press P/R/O/Q to adjustPress Keystone to set theAdjustment with R/O position Sphere correctionSwitching the Input Mode Input listHdmi 1/2, Component and Computer buttons Resize Mode Press Resize on the remote control or on the projectorSelecting the Picture Mode Operating with the Remote ControlAdjusting the Image Press image adjustment buttonsSwitching the Eco+Quiet Mode Switching the Iris SettingAuto Sync Auto Sync Adjustment Hiding the Menu Temporarily Menu HideMenu Items Picture menuRGB 3D Menu Press Q or O and select Picture to adjust Using the Menu ScreenMenu Selections Adjustments Press MenuPress O or Q to adjust the item selected To adjust the projected image while watching itPress P or R and select Bright to adjust Press EnterPicture Adjustment Picture Menu Selecting the Picture ModeMenu operation n Using the Advanced Adjusting the Image Switching the Iris Setting Eco+QuietCustom Gamma Adjusting the ColorsAdjust the curve to adjust the image brightness PickerS. color adjustment screen Setting Detail Enhancement Adjusting the Bright BoostSelecting the Film Mode Resetting All Adjustment ItemsComputer Image Adjustment SIG-ADJ Menu Setting the ResolutionAdjusting the Dynamic Range Signal Type SettingSetting the Video Setup Signal Info2Adjusting the Image Position Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode TriggerSetting On-screen Display Adjusting the Projected Image SCR-ADJ Menu ContinueAdjusting the Overscan Black MaskReversing/Inverting Projected Images See page 22 for details of Projection PRJ ModeSelecting the Menu Screen Position Selecting the On-screen Display LanguageSetting No Operation Off Mode Setting the Power Save Mode Economy ModeEconomy Mode Setting the System Standby Function System Standby Setting One Touch PlaySetting the One-Touch Playback Function One Touch Play Setting the Input Terminal Names Input Name Fan Mode Setting Adjusting the Projector Function PRJ-ADJ Menu Setting the Demo Mode Turning LED OffReturning to the Default Settings Lamp Timer LifeSelect Password, then press Q Setting Up the Projector Network Environment Network MenuSetting a Password On the projector, pressReturning to Default Settings Network Dhcp Client SettingTCP/IP Setting Enter IP Address using P, R, Q and O, then press EnterConﬁrming the Projector Information You can conﬁrm the following itemsPrecautions on using the 3D Glasses Precautions on installing the IR emitterEnjoying 3D Image Viewing Precautions on viewing 3D images As you get more comfortable viewing 3D imagesEpilepsy Supplied Accessories for the 3D Glasses Part NamesRemove the button cell battery Before Using the 3D GlassesReplacing the Button Cell Battery Close the battery coverUsing the 3D Glasses Attaching the Nose PadAttaching the 3D Glasses Band Position the IR emitter Connecting the IR Emitter to the ProjectorInstall the IR emitter unit to the stand To 3D Synchro terminal IR emitter cableViewing 3D Images When 3D Auto Change is set to NoWhen 3D Auto Change is set to Yes Turn on the 3D Glasses and place them over your eyesPress 3D Menu Press P/R to select 3D Press O/Q to select On or Off3D Format 3D Depth Adjust3D Auto Change Viewing Time InfoSetting the 3D Format Menu 3D Glasses lenses Speciﬁcations 3D Glasses S 0 8 B Manufacture number ColorDimensions Effective DistanceCleaning the lens or lens cover MaintenanceCleaning the projector Cleaning the exhaust and intake ventsMaintenance Indicators About the temperature warning indicatorAbout the lamp indicator Red on Abnormally high Are high Lower than 95F +35ºC Regarding the Lamp LampReplacing the Lamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Lamp unitResetting the Lamp Timer Compatibility Chart ComputerDTV Troubleshooting 23-27Problem Check 68-70 For Sharp Assistance Speciﬁcations HdmiDimensions Index